Forum: 12th & 10th On Road
23-02-2019
|
|
Replies: 2
Views: 3,308
1/12th National Hot Rod
Hi
I would like to start racing again, but this time a lot cheaper.
I would like to race in 1/12 National Hot Rods as this seems like a 'controlled' formula.
I not raced or used 1s Lipos,...
|
Forum:  Schumacher
29-04-2016
|
|
Replies: 5
Views: 2,210
|
|
Forum: Electrics
29-04-2016
|
|
Replies: 7
Views: 1,167
Thanks, I used to race 20 years ago with the...
Thanks, I used to race 20 years ago with the brushed motors, and used to oil them every couple of runs.
Would that be case for the main bearings on the car, they have red seals (Schumacher)
...
|
|
Forum: Schumacher
28-04-2016
|
|
Replies: 5
Views: 2,210
KF2 gearing
Would 27/76T be ok with a circuit with long straight but twisty infield running standard mod 0 profilr on speed passion pro ?
|
|
Forum: Electrics
28-04-2016
|
|
Replies: 7
Views: 1,167
|
|
Forum: General Race Chat
18-04-2016
|
|
Replies: 38
Views: 6,140
Great Service
I had brilliant service from them and drove over 70 miles as that is the nearest stockist of Schumacher parts for me. Had great contact throughout email and not ebay.
|
|
Forum: Electrics
18-04-2016
|
|
Replies: 7
Views: 1,167
bueshless oiling
Hi what is best period to oil the bearing on a brushless motor.
I ran for the first time off road and was amazed by the speed and duration and the motor did not run hot.
Thanks
Matt
|
|
Forum: Schumacher
11-04-2016
|
|
Replies: 6
Views: 1,557
Velcro body hold on
Hi does anyone use velcro to hold your body shells on, I think this would be easier on my KF2 as the body is very tight anyway. Also what is a decent replacement screw set supplier as I have lost a...
|
|
Forum: 1/10th OFF ROAD
10-04-2016
|
|
Replies: 4
Views: 1,986
|
|
Forum: 1/10th OFF ROAD
10-04-2016
|
|
Replies: 4
Views: 1,986
tool set
Does anyone make a descent nut driver and hex druver set for sensible money. Need to get a decent tool set up for my KF2.
|
|
Forum: Schumacher
09-04-2016
|
|
Replies: 28
Views: 4,735
|
|
Forum: Schumacher
08-04-2016
|
|
Replies: 5
Views: 2,210
KF2 Gearing
Hi what would be a reasonable gear ration pin to spur for a 10.5 motor running on Astro with a fairly long straight. Have a Speed Passion Reventon Pro Speed Controller in a brand new KF2 SE. Thanks.
|
|
Forum: Electrics
07-04-2016
|
|
Replies: 5
Views: 841
Gearing
Thanks for the info, but does anyone have any idea on gearing for a 10.5T, the circuit has quite a long straight but can be very technical infield.
|
|
Forum: 1/10th OFF ROAD
07-04-2016
|
|
Replies: 2
Views: 1,275
Front width
Hi I have just built my KF2 but the front end is wider than the rear, Is this OK, just look a bit strange. But then again I am used to 4wd and this is the first 2WD car I have built.
Also what is...
|
|
Forum: Electrics
07-04-2016
|
|
Replies: 5
Views: 841
|
|
Forum: Electrics
06-04-2016
|
|
Replies: 5
Views: 841
Reventon Pro 1.1 10.5T Setup
Hi All,
I am about to start racing again this weekend, and have everything built and installed.
What ESC setting should I use for 10.5 motor using a Cougar KF2 SE.
Also what gearing should...
|
|
Forum: Electrics
05-04-2016
|
|
Replies: 22
Views: 3,111
transponder
Thank you, the Harry light flashes when all is ok, its this correct. Just need to find out the transponder number as bought this second hand.
|
|
Forum: Electrics
05-04-2016
|
|
Replies: 22
Views: 3,111
Gemini X
Hi, Just getting everything ready before the big switch on, is there anything I need to prepared to do. I have reset the transmitter so everything is set to 100%. Just dont want something to go bang,...
|
|
Forum: Electrics
05-04-2016
|
|
Replies: 22
Views: 3,111
Gemini X
Hi, Just getting everything ready before the big switch on, is there anything I need to prepared to do. I have reset the transmitter so everything is set to 100%. Just dont want something to go bang,...
|
|
Forum: Electrics
04-04-2016
|
|
Replies: 15
Views: 2,135
Reventon Pro 1.1 set up problem
Thank you, I reset the Transmitter, and now at least the motor runs, I havent installed any electrics at the moment as was trying to get the steering straight. All Good fun, still loads to do and...
|
|
Forum: Electrics
04-04-2016
|
|
Replies: 15
Views: 2,135
Reventon Pro 1.1 set up problem
Hi I am trying to set up my new Reventon Pro 1.1 speedo.
Have connected everything correctly inc sensor wire and tried to callibrate it. All the usual beeps are ok, and steering servo works, but...
|
|
Forum: 1/10th OFF ROAD
02-04-2016
|
|
Replies: 18
Views: 3,317
Schumacher white fronts
Hi I have front minispike 2 silver on std front hex wheels. Do these need inserts as they feel very soft on the wheels
Also does that goes the same for the cut stagger low profiles on narrow...
|
|
Forum: Schumacher
02-04-2016
|
|
Replies: 1
Views: 1,187
Kf2se bodyshell
Hi is this plastic protection on both sides if the body shell that need to be removed before painting.
It's been over 10 years since a painted a shell and do not remember plastic protection...
|
|
Forum: 1/10th OFF ROAD
28-03-2016
|
|
Replies: 13
Views: 2,148
|
|
Forum: Schumacher
27-03-2016
|
|
Replies: 28
Views: 4,735
How got all the allen drivers, and yes they do...
How got all the allen drivers, and yes they do make assembling it easier than farting around with allen keys. Just spotted my first error had the belt the wrong side of the front teasioner - oops -...
|
