Go Back   oOple.com Forums > Search Forums
Reload this Page Search Results
Register FAQ Community Calendar Today's Posts Search

Showing results 1 to 22 of 22
Search took 0.00 seconds. Search: Posts Made By: Bike Racer
Forum: Yokomo 15-11-2011
Replies: 20
Views: 2,613
Posted By Bike Racer
I'm pretty sure I used an Associated TC3 bars on...

I'm pretty sure I used an Associated TC3 bars on my BX.
Forum: Yokomo 04-11-2011
Replies: 5
Views: 986
Posted By Bike Racer
Relatively direct fit. For the original MR-4BX (2...

Relatively direct fit. For the original MR-4BX (2 piece chassis) or Factory (one piece chassis) changing to the B4 hubs and CVDs was an incredible mod. The car felt so much more connected with the...
Forum: Yokomo 22-10-2011
Replies: 5
Views: 986
Posted By Bike Racer
Associated B4 CVDs are a direct fit, but you have...

Associated B4 CVDs are a direct fit, but you have to use B4 hubs too because the Yok bearings are metric. To use the B4 hubs you need to drill out the hinge pin hole in the arm, the B4 uses thicker...
Forum: Yokomo 06-05-2010
Replies: 2
Views: 604
Posted By Bike Racer
I ran associated shock shafts front and rear in...

I ran associated shock shafts front and rear in my BX. The Associated shafts are a little thicker than the Yoke shafts, and easier to get ahold of.
Forum: X-Factory 03-03-2010
Replies: 7
Views: 1,280
Posted By Bike Racer
I have the Losi quick change mounts and they are...

I have the Losi quick change mounts and they are JUST long enough to pass through the AE shock tower and get a nut on them. The Losi tower must be a bit thinner.
Forum: X-Factory 29-12-2009
Replies: 18
Views: 2,907
Posted By Bike Racer
Looks like your servo is mounted in the rear...

Looks like your servo is mounted in the rear mounting holes?? I think all the setups I've seen use the front holes.
Forum: Yokomo 29-09-2009
Replies: 7
Views: 1,819
Posted By Bike Racer
I don't use the belt tensioner in either my...

I don't use the belt tensioner in either my standard BX, or on the BX Worlds car. On the standard BX the rear of the rear top deck is a little bit lower than the front, so some of the packs are...
Forum: Yokomo 20-01-2009
Replies: 5
Views: 1,230
Posted By Bike Racer
Fronts wear more because the rear is so hooked up...

Fronts wear more because the rear is so hooked up the front end pushes, therefore wears the tires more.
Forum: Yokomo 17-01-2009
Replies: 7
Views: 1,819
Posted By Bike Racer
Use carbon fiber braces and standoffs from...

Use carbon fiber braces and standoffs from Diggity Designs. There are no mods needed. The SMC packs should be the hot setup.

http://www.diggitydesigns.com/D3_OffRoad_Products_Yokomo.html
Forum: Yokomo 08-01-2009
Replies: 75
Views: 12,637
Posted By Bike Racer
I think most use Rayspeed aluminum hubs (I use...

I think most use Rayspeed aluminum hubs (I use Trinity) to keep the bling factor going. They also come in .5* and 1* versions where stock B4 plastic hubs don't come in anything other than 0*. There...
Forum: Yokomo 05-12-2008
Replies: 7
Views: 1,819
Posted By Bike Racer
I've been working on this in theory anyway. ...

I've been working on this in theory anyway.

The Trakpower 4800 is 1.2" tall, and the most I can see fitting under the rear topdeck is 1.0". The SMC saddle packs are right at 1.0", so they SHOULD...
Forum: Yokomo 18-11-2008
Replies: 10
Views: 1,749
Posted By Bike Racer
Sounds pretty stiff to me. I run a non worlds BX,...

Sounds pretty stiff to me. I run a non worlds BX, so I'm not sure how my setup would work, but one of the guys at my track runs a worlds car and this is his setup.

Front:
Shocks inside...
Forum: Yokomo 05-10-2008
Replies: 6
Views: 1,331
Posted By Bike Racer
Yep. With crappy batteries you need more...

Yep. With crappy batteries you need more motor..........
Forum: Yokomo 30-09-2008
Replies: 6
Views: 1,331
Posted By Bike Racer
I run an Orion 5.5 and I have it geared 18/87 and...

I run an Orion 5.5 and I have it geared 18/87 and it's pretty much perfect.
Forum: Yokomo 28-09-2008
Replies: 3
Views: 1,289
Posted By Bike Racer
Here: ...

Here:

http://dcracing.co.uk/dcrshop/index.php?cPath=68_112_156_158&osCsid=404a3fb7563697ed943459b05cb9eef3
Forum: Yokomo 17-07-2008
Replies: 86
Views: 19,312
Posted By Bike Racer
If they're smart they'll send one to Jimmy ASAP....

If they're smart they'll send one to Jimmy ASAP. Jimmy's reviews are awesome, and I know A LOT of people read them for the inside scoop.
Forum: Yokomo 12-07-2008
Replies: 10
Views: 1,754
Posted By Bike Racer
What is the fan that is blowing on the motor...

What is the fan that is blowing on the motor mounted to?

There is a guy over here in the states that make carbon fiber trays the lipo packs sit in to stop lateral movement. He has them for the...
Forum: Yokomo 29-11-2007
Replies: 3
Views: 1,423
Posted By Bike Racer
Will do, thanks.

Will do, thanks.
Forum: Yokomo 29-11-2007
Replies: 3
Views: 1,423
Posted By Bike Racer
Anyone?????? How about a team member to...

Anyone??????

How about a team member to contact?
Forum: Yokomo 28-11-2007
Replies: 3
Views: 1,423
Posted By Bike Racer
Anti-squat

Does anyone know FOR SURE what the anti-squat settings are with the aluminum shim in place on the original MR-4BX?

How about when you flip the rear pivot over, how much does that change?

I...
Forum: Yokomo 26-10-2007
Replies: 40
Views: 7,236
Posted By Bike Racer
Worlds Edition released

Follow the link.
http://www.redrc.net/2007/10/yokomo-mr-4bx-world-spec-kit/

Conversion kit available.

Nice.
Forum: Yokomo 03-09-2007
Replies: 1
Views: 1,291
Posted By Bike Racer
New to the MR-4BX

Hey guys, I just picked up a used BX, and I'm just getting started working on the setup. I have the original version, not the Factory. I have several questions.

What is the stock anti-squat...
Showing results 1 to 22 of 22

 
Forum Jump

All times are GMT. The time now is 05:23 PM.

Contact Us - oOple.com - Archive - Top

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
oOple.com