Go Back   oOple.com Forums > Search Forums
Reload this Page Search Results
Register FAQ Community Calendar Today's Posts Search

Showing results 1 to 14 of 14
Search took 0.00 seconds. Search: Posts Made By: xrider
Forum: Hot Bodies / HPI 09-10-2008
Replies: 271
Views: 52,261
Posted By xrider
Travis posted on rctech March 2009.:(

Travis posted on rctech March 2009.:(
Forum: Hot Bodies / HPI 21-04-2008
Replies: 271
Views: 52,261
Posted By xrider
Just thought I would kick start this thread...

Just thought I would kick start this thread again. Any news on a release date? Or pictures of the shell?
Forum: Tamiya 07-12-2007
Replies: 8
Views: 1,489
Posted By xrider
Thursday I moved my inner ball stud to the middle...

Thursday I moved my inner ball stud to the middle holes, and lowered the ball stud height on my rear alloy hubs. WOW! What a difference that made, the rear feels really planted now. Thanks for all...
Forum: Tamiya 17-11-2007
Replies: 8
Views: 1,489
Posted By xrider
I am running AE blues in front with the middle...

I am running AE blues in front with the middle pistons, and 45 weight. Rear are AE silvers with the middle pistons and 40 weight. Thanks for everyones input.
Forum: Tamiya 16-11-2007
Replies: 8
Views: 1,489
Posted By xrider
What effect will I get by removing the two...

What effect will I get by removing the two spacers in the kit setup under the rear upper mount? Hence lowering the inner camber link, same a shrtening it?
Forum: Tamiya 16-11-2007
Replies: 8
Views: 1,489
Posted By xrider
I have traction. It feels like when I get in the...

I have traction. It feels like when I get in the throttle it leans back and forth coming out of a corner. Right now I am on the inner most hole on the upper mount, close to diffs, and center hole in...
Forum: Tamiya 15-11-2007
Replies: 8
Views: 1,489
Posted By xrider
501X Sway Bar, will it reduce the rear from being loose?

OK,

So far this 4wd is by far the best one I have owned. In regards to a XXX-4, XX-4, and a BJ4WE, in my opinion. The only problem I seem to have is when I come out of a corner, and the weight...
Forum: Tamiya 06-11-2007
Replies: 2
Views: 1,151
Posted By xrider
Going from stock 96T spur to AE 87T spur

I was curious as to what you will achieve by running the smaller diameter spurs on the TRF501X. The track I run on is roughly 70ftX120ft. About a 90ft straight, but there is a huge quad that when you...
Forum: Tamiya 04-11-2007
Replies: 4
Views: 1,191
Posted By xrider
Thanks for the info. I guess I should have asked...

Thanks for the info. I guess I should have asked the question before I purchased the parts. I may still use the rod guide kit though. The shocks do seem to leak more than my AE ones, or others for...
Forum: Tamiya 04-11-2007
Replies: 13
Views: 1,766
Posted By xrider
Your right, after I upgraded all the pulleys and...

Your right, after I upgraded all the pulleys and belts I also felt the tension was lighter than the instruction sheet they supply. I increased the rear two notches. The front seems ok for now. Good...
Forum: Team Associated 04-11-2007
Replies: 9
Views: 1,765
Posted By xrider
Here at my track we run 10 minute mains. With the...

Here at my track we run 10 minute mains. With the Orion Lipo 3200 it is more than enough to complete the race with a 13.5. We don't run any weight in our cars, except an ounce under the transmission,...
Forum: Tamiya 04-11-2007
Replies: 4
Views: 1,191
Posted By xrider
TRF501X Low Friction Rod Guide set and Delrin Pistons

So I noticed with the stock pistons there is a considerable amount of play with the piston in the shock body. I have ordered the Hop Up low friction rod guide sets, and delrin low friction pistons....
Forum: Tamiya 04-11-2007
Replies: 4
Views: 1,151
Posted By xrider
I run on an indoor dirt track with about a 90...

I run on an indoor dirt track with about a 90 foot straight and a huge quad. I am geared at 21/96 with a 5.5, and the temps are right at 165 on both esc and motor. In practic it was only temping 120...
Forum: Tamiya 04-11-2007
Replies: 13
Views: 1,766
Posted By xrider
If you are missing teeth on the belt it could be...

If you are missing teeth on the belt it could be that it is too loose. It can bounce on the rear top deck and catch on the edge of the carbon fiber and possibly pull some of the rubber teeth off.
Showing results 1 to 14 of 14

 
Forum Jump

All times are GMT. The time now is 03:11 AM.

Contact Us - oOple.com - Archive - Top

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
oOple.com