Go Back   oOple.com Forums > Search Forums

Showing results 1 to 25 of 237
Search took 0.01 seconds.
Search: Posts Made By: Dadio
Forum: Vintage RC 1 Day Ago
Replies: 33
Views: 1,399
Posted By Dadio
Wish this lot was all genuine , its all...

Wish this lot was all genuine , its all development parts . I'm not obsessed :shock:
https://i.imgur.com/MXzQgLdl.jpg
Forum: Vintage RC 5 Days Ago
Replies: 33
Views: 1,399
Posted By Dadio
I went back to the plain nylon c hubs and i think...

I went back to the plain nylon c hubs and i think that's working better . I got dogged off with the constant failure of the one way roller bearings in the front drive hubs so i drew up and printed...
Forum: Vintage RC 1 Week Ago
Replies: 33
Views: 1,399
Posted By Dadio
The first few carbon fiber fill nylon parts are...

The first few carbon fiber fill nylon parts are rolling off , the first prints were not so good as even out of the sealed bag brand new the filament was damp and needed drying , after drying the...
Forum: Vintage RC 3 Weeks Ago
Replies: 33
Views: 1,399
Posted By Dadio
Just free hand , I've never seen in the flesh the...

Just free hand , I've never seen in the flesh the real parts and i adapted it a bit , the trailing arms to mach are on their way.
https://i.imgur.com/oRjXGmxl.jpg
https://i.imgur.com/jajjEMfl.jpg...
Forum: Vintage RC 3 Weeks Ago
Replies: 33
Views: 1,399
Posted By Dadio
Oops , looks like another part needs the nylon...

Oops , looks like another part needs the nylon treatment , this broke landing a jump :cry: Next month I'll get some carbon fill nylon , its easier to print as it warps less , its more rigid and its...
Forum: Vintage RC 3 Weeks Ago
Replies: 33
Views: 1,399
Posted By Dadio
Fully Nylon front suspension and TPU body , the...

Fully Nylon front suspension and TPU body , the PLA body started cracking and it rattled something awful so made the new one in TPU a flexible plastic , sorry about the colour its all i had ....
Forum: Vintage RC 4 Weeks Ago
Replies: 3
Views: 177
Posted By Dadio
If you cannot source a complete car straight away...

If you cannot source a complete car straight away it might be worth starting by asking what parts are most rare and easily broken , many cars end up on a display shelf because its virtually...
Forum: Vintage RC 4 Weeks Ago
Replies: 33
Views: 1,399
Posted By Dadio
At some point in the near future it should be on...

At some point in the near future it should be on Shapeways , I'm not releasing the files into the wild at the moment ,sorry but it represents quite a chunk of work .
Forum: Vintage RC 4 Weeks Ago
Replies: 33
Views: 1,399
Posted By Dadio
First reinforced top arm , I've made it so i no...

First reinforced top arm , I've made it so i no longer need a nut but the crew taps into the rear pivot , its made of nylon as well so much more impact resistant .
https://i.imgur.com/bUIVfu7l.jpg...
Forum: Vintage RC 4 Weeks Ago
Replies: 33
Views: 1,399
Posted By Dadio
I finally got some video footage , also had my...

I finally got some video footage , also had my first part failure , both front suspension top arms cracked at the inner rear mounting , those parts are some of the last parts on the car that are...
Forum: Vintage RC 4 Weeks Ago
Replies: 33
Views: 1,399
Posted By Dadio
New body , first picture is just as it finishes...

New body , first picture is just as it finishes still on the print bed .
https://i.imgur.com/4e8caGLl.jpg
Uncut
https://i.imgur.com/BHOtEupl.jpg
And fitted
https://i.imgur.com/XEuUSnkl.jpg...
Forum: Vintage RC 4 Weeks Ago
Replies: 33
Views: 1,399
Posted By Dadio
I had some minor teething trouble with the...

I had some minor teething trouble with the gearbox design yesterday but its been simply rectified , I have a new version of the body printing as well .
I'm hoping to get some video later but its a...
Forum: Vintage RC 4 Weeks Ago
Replies: 33
Views: 1,399
Posted By Dadio
Kyosho chain adapted sprockets designed , printed...

Kyosho chain adapted sprockets designed , printed and tested , its a complete car !
https://i.imgur.com/pLBaeK0l.jpg
https://i.imgur.com/GELg0W0l.jpg
I had a spare Kyosho chain so this was...
Forum: Vintage RC 4 Weeks Ago
Replies: 33
Views: 1,399
Posted By Dadio
Just a bit of fun , i modeled up a rough copy of...

Just a bit of fun , i modeled up a rough copy of a Bolink Funco half body , its not quite right , the cab is too long , this is printed in Vase or Spiral mode , just one layer or 0.4mm thick ,...
Forum: Vintage RC 4 Weeks Ago
Replies: 33
Views: 1,399
Posted By Dadio
Well it was and still is "OFFICAL WORLD WIDE...

Well it was and still is "OFFICAL WORLD WIDE SILLY GRIN DAY" :D :D :D
The front shafts arrived today and fit perfectly , its still short of a chain so only rear wheel drive but she runs !...
Forum: Vintage RC 05-08-2019
Replies: 33
Views: 1,399
Posted By Dadio
Redesigned rear arms , the white one was one of...

Redesigned rear arms , the white one was one of the first models i made in Fusion 360 and although i was pleased with it then i later deleted it as it was too flawed , so the two black arms are the...
Forum: Vintage RC 04-08-2019
Replies: 33
Views: 1,399
Posted By Dadio
Chain guard , new version of rear arms that are...

Chain guard , new version of rear arms that are much more accurately copied are printing now .
https://i.imgur.com/SRwoxT9l.jpg
https://i.imgur.com/i73zMCll.jpg
Forum: Vintage RC 03-08-2019
Replies: 33
Views: 1,399
Posted By Dadio
Made up a very simple roll bar to mount shocks at...

Made up a very simple roll bar to mount shocks at the rear and fitted some Pargu front shock mounts with a cheap shock i had laying about , its still got genuine rear shafts , no chain or front...
Forum: Vintage RC 02-08-2019
Replies: 33
Views: 1,399
Posted By Dadio
All the new bits fitted , the eagle eyed among...

All the new bits fitted , the eagle eyed among you might notice I've done some vapor smoothing to the ABS parts , this smooths out a lot of the layer lines and gives a more shiny surface ,it also...
Forum: Vintage RC 31-07-2019
Replies: 33
Views: 1,399
Posted By Dadio
Found a little time to modify some Scorpion re re...

Found a little time to modify some Scorpion re re rear axles to make front axles , these will hold the roller hub on with a regular nut rather than a C clip , i had to first anneal them then turn...
Forum: Vintage RC 24-07-2019
Replies: 33
Views: 1,399
Posted By Dadio
Front drive spindle finished . ...

Front drive spindle finished .
https://i.imgur.com/8DDEAVcl.jpg
https://i.imgur.com/2fPu2z7l.jpg
Forum: Vintage RC 17-07-2019
Replies: 33
Views: 1,399
Posted By Dadio
I have the sprockets already modelled and printed...

I have the sprockets already modelled and printed ,you can see the rear one on the printed gearbox pictures , I already run kyosho sprockets and chain on my upgraded runner , its even got a front...
Forum: Vintage RC 13-07-2019
Replies: 33
Views: 1,399
Posted By Dadio
Now with added Diffy goodness , i still need to...

Now with added Diffy goodness , i still need to finish the outdrives but its all working, i had it running for a few minutes without load , it was a little rough at first but free'd up well . Shown...
Forum: Vintage RC 12-07-2019
Replies: 33
Views: 1,399
Posted By Dadio
The latest version gearbox is finished and all as...

The latest version gearbox is finished and all as good as i could hope for , more pictures I'm afraid , both proto-gearboxes and all the proto-gears then some shots of the genuine article and my...
Forum: Vintage RC 11-07-2019
Replies: 33
Views: 1,399
Posted By Dadio
Thanks I have the gears all running smooth now...

Thanks
I have the gears all running smooth now and I'm printing what i hope will be a final design gearbox , i threw it all together as well for a look .
https://i.imgur.com/X2xwtWRl.jpg...
Showing results 1 to 25 of 237

 
Forum Jump

All times are GMT. The time now is 09:14 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
oOple.com