Go Back   oOple.com Forums > Search Forums
Reload this Page Search Results
Register FAQ Community Calendar Today's Posts Search

Showing results 1 to 17 of 17
Search took 0.00 seconds. Search: Posts Made By: WailinOnYa
Forum: Tamiya 13-12-2014
Replies: 1
Views: 1,331
Posted By WailinOnYa
TRF502 front shock tower fit TRF511?

Anyone here own both cars? Will a 502 front shock tower bolt up to a 511 upper bulkhead mount or is the hole spacing different? This is a possible emergency replacement it it will work. Thanks in...
Forum: Tamiya 23-08-2013
Replies: 22
Views: 4,332
Posted By WailinOnYa
On a side note, I took some 38 tooth pulleys from...

On a side note, I took some 38 tooth pulleys from a 3racing Sakura to see if they would fit with the shorter 369mm belts. It was a no go, the belts were used so they had a bit more stretch to them,...
Forum: Tamiya 22-08-2013
Replies: 22
Views: 4,332
Posted By WailinOnYa
Your lucky! I live in the U.S. and Tamiya USA...

Your lucky! I live in the U.S. and Tamiya USA took forever even to show the 511 Upgrade set to be available, it took months after it showed up on the USA site when other countries Like the UK already...
Forum: Tamiya 21-08-2013
Replies: 22
Views: 4,332
Posted By WailinOnYa
The belts are 372mm 124 tooth count, just one...

The belts are 372mm 124 tooth count, just one more tooth than the older 369mm belts. The part # is 16248001, problem is this part # is not listed and does not appear to be available as of yet! I also...
Forum: Tamiya 02-05-2013
Replies: 22
Views: 4,332
Posted By WailinOnYa
Will the 369mm belts fit the larger 39 pulleys on...

Will the 369mm belts fit the larger 39 pulleys on the loosest setting on the cams?
Forum: Tamiya 14-10-2012
Replies: 2
Views: 1,195
Posted By WailinOnYa
Won't work! The durango pistons are larger/bigger...

Won't work! The durango pistons are larger/bigger diameter, slightly larger bore, they are equivelant to a losi in diameter. The Tamiyas are on the small side, they are even a bit smaller than...
Forum: Tamiya 15-09-2010
Replies: 2
Views: 951
Posted By WailinOnYa
Not sure of any guide, but in general you want to...

Not sure of any guide, but in general you want to run the belts as loose as possible without them slipping/skipping teeth. After you have run quite a few belt cars or even one belt car for a long...
Forum: Tamiya 19-02-2010
Replies: 23
Views: 3,140
Posted By WailinOnYa
You might want to try checking your local hobby...

You might want to try checking your local hobby shops for spring steel rods, most hobby shops carry them for building projects. If you can find the diameter you need, (bring some calipers with you)....
Forum: Tamiya 31-07-2008
Replies: 27
Views: 3,479
Posted By WailinOnYa
I guess one of the larger aluminum looking...

I guess one of the larger aluminum looking spacers in the pic may be the keyed part for one of the pulleys for the rear, now that you mention it. It's hard to tell because you can't see any notches...
Forum: Tamiya 31-07-2008
Replies: 27
Views: 3,479
Posted By WailinOnYa
I see that Stella Models has these listed on Ebay...

I see that Stella Models has these listed on Ebay at this time. It says for use with the 501X worlds or DB01 cars but not for use with 501X/original 501X. Is there a difference between the layshafts...
Forum: Tamiya 12-07-2008
Replies: 27
Views: 3,479
Posted By WailinOnYa
The big question for me is if anyone knows...

The big question for me is if anyone knows whether or not this layshaft oneway is adjustable for more or less freewheel like the Yokomo unit or is it full freewheel all the time, set it and forget it!
Forum: Tamiya 08-04-2008
Replies: 10
Views: 1,966
Posted By WailinOnYa
They are Big, The pack wouldn't even fit between...

They are Big, The pack wouldn't even fit between the battery hold down posts! You can barely shimmy it between the narrow portion of the posts and then they are flexing, by the time you get it down...
Forum: Tamiya 03-03-2008
Replies: 14
Views: 1,840
Posted By WailinOnYa
Never had that problem, but I don't have the...

Never had that problem, but I don't have the Nitride shafts, I have the original 501X and not the Worlds. I think the binding is inrelation to the machined pistons which have such a close tolerance...
Forum: News 27-02-2008
Replies: 9
Views: 6,395
Posted By WailinOnYa
Actually it looks as though the saddles butted...

Actually it looks as though the saddles butted together would only be 3mm longer, so not a huge amount according to the dimensions on the TrakPower site!
Forum: News 27-02-2008
Replies: 9
Views: 6,395
Posted By WailinOnYa
I don't think they are the same length butted...

I don't think they are the same length butted together to be equivelant to a regular stick pack, I imagine it would wind up noticably longer, not positive on this though. The question I have is that...
Forum: Xtreme - VEGA 11-02-2008
Replies: 17
Views: 1,888
Posted By WailinOnYa
I have done that very same thing to two of the...

I have done that very same thing to two of the Graphite/lightweight chassis on my X10. If I hadn't seen/done it for myself I would have thought it would be impossible as thick as the composite is in...
Forum: Tamiya 01-02-2008
Replies: 120
Views: 11,014
Posted By WailinOnYa
I am also interested in two sets of these, black...

I am also interested in two sets of these, black and white. I sent you an Email, but never received a reply. What is the $ you are asking for these also need to know Shipping $ to the U.S. Any info...
Showing results 1 to 17 of 17

 
Forum Jump

All times are GMT. The time now is 11:00 PM.

Contact Us - oOple.com - Archive - Top

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
oOple.com