|
#1
|
||||
|
||||
Original x6 to x6 Cube upgrade
SO guys after seeing Paul's Video I'm Extremly excited to see the x6 cube as many are !!!
BUT how do I go about it ?? CAN and if so How could I upgrade my original x6 ??? Would it b cheaper to buy a squared rolling chassis and convert to a cubed Cheers guys |
#2
|
||||
|
||||
Looking at pics and videos it should be easier to convert original x6 to x6 cubed as it uses original front which is all good as I have 2 to change( price dependent of corse )
__________________
Schumacher kf Schumacher sv2 Durango Dex210 Carisma gtb x2 Schumacher gt12 x2 |
#3
|
|||
|
|||
Quote:
Assuming it is 4 gear, all you will need will be the Cubed "Ugrade Kit" (not the more expensive "Conversion" kit) and you will need the X6 Squared rear wishbones (XF3012) and hinge bushes (XF6142)and possibly some servo mounts too otherwise you are good to go......
__________________
ORCA - LC RACING - RUDDOG PRODUCTS - JCONCEPTS - ALPHA PLUS - TEKIN RACING - ULTRAPOWER AVID R/C - VAMPIRE RACING - EXOTEK RACING - LUNSFORD RACING - X-FACTORY - TUNING HAUS - WTF AME - RAGE R/C - REVOLUTION DESIGN RACING PRODUCTS - McKUNE DESIGN - TEAM AZARASHI X-PARTZ - PHAT BODIES - RACERS EDGE - RM2 - DIRT RACING PRODUCTS - DMS INSERTZ TKR GRAPHICS - BF MATERIALS - BATAN - DMS PARTZ - TEAM AJ Tel : (01923) 816636
|
#4
|
||||
|
||||
Hi Darren .....
I was hoping u would reply :-) ...... I can only assume its the older 3 gear version , I'm not 100% sure thou as I brought the car 2nd hand a while ago . Is there an easy way for a newbie like me to tell ?? Thanks for everything Craig |
#5
|
|||
|
|||
Looking from the front, which side is the slipper nut? If its on the right, you have the 4 gear tranny, on the left, the 3 gear.
HTH |
#6
|
|||
|
|||
Also if you simply look at the gearbox case it has circular shapes around the gears that it houses, the largest being at the bottom which is the diff then smaller ones a the top for the idler (or idlers x 2 in a 4 gear) and of course the top shaft gear, juts count if you have 3 or 4.
Or alternatively if you are still unsure, remove and open up the gearbox and count'em, 3 or 4? If you do have a 3 gear, additionally to the list above you will need the 4 gear transmission case (XF5001), another idler gear shaft (XF5201), a pair of idler gear bearings (XF6202) and an Associated B4 idler gear (AS9360), a 4 gear motor plate of your choice - you have a large selection to choose from depending on your taste - standard kit alloy version (XF1232), or optional ones such as X-Factory Real Men Wear Black, black version (XF1233), E-Speed blue milled version (ES009), DDP blue milled version (DDP024), DMS Partz carbon fibre version (DMS133) or even the Optimized RC ones in red or blue (OP002 or OP004)
__________________
ORCA - LC RACING - RUDDOG PRODUCTS - JCONCEPTS - ALPHA PLUS - TEKIN RACING - ULTRAPOWER AVID R/C - VAMPIRE RACING - EXOTEK RACING - LUNSFORD RACING - X-FACTORY - TUNING HAUS - WTF AME - RAGE R/C - REVOLUTION DESIGN RACING PRODUCTS - McKUNE DESIGN - TEAM AZARASHI X-PARTZ - PHAT BODIES - RACERS EDGE - RM2 - DIRT RACING PRODUCTS - DMS INSERTZ TKR GRAPHICS - BF MATERIALS - BATAN - DMS PARTZ - TEAM AJ Tel : (01923) 816636
|
#7
|
||||
|
||||
How many flavors is that, Darren???
|
#8
|
||||
|
||||
Quote:
By the way thanks for your pics Darren, they look very good.
__________________
|
#9
|
|||
|
|||
Quote:
The B4 motor plates will not fit.
__________________
ORCA - LC RACING - RUDDOG PRODUCTS - JCONCEPTS - ALPHA PLUS - TEKIN RACING - ULTRAPOWER AVID R/C - VAMPIRE RACING - EXOTEK RACING - LUNSFORD RACING - X-FACTORY - TUNING HAUS - WTF AME - RAGE R/C - REVOLUTION DESIGN RACING PRODUCTS - McKUNE DESIGN - TEAM AZARASHI X-PARTZ - PHAT BODIES - RACERS EDGE - RM2 - DIRT RACING PRODUCTS - DMS INSERTZ TKR GRAPHICS - BF MATERIALS - BATAN - DMS PARTZ - TEAM AJ Tel : (01923) 816636
Last edited by Col; 19-05-2013 at 06:30 PM. |
#10
|
||||
|
||||
We wanted very much to not have to produce a gear cover. The great majority of our Team experience and the majority of the Family experience is that a gear cover is not needed when the body is snug. And the new Cubed body is snug.
However, some Family experience in short course, and, to a lesser extent, in stadium truck, shows that at some tracks a gear cover might be helpful in those classes where the body fits more loosely. I run only stadium truck and have never had the slightest concern in this area. My driving skill is another matter! LOL Therefore, the new #1234 motor plate will include two tapped holes for a gear cover. The AE one will not fit; Paul worked for almost a week trying to make it fit so we did not need to make a gear cover, and it simply will not. So, at some point in the future we intend to make a gear cover; however the Cubed will be released without it and the X - 60CF and SCX - 60CF will continue without. |
#11
|
||||
|
||||
Well guys last night had the car checked over and iDO have a 4 gear transmission !!!!
But a few guys have mentioned that as the cubed is +9mm it wouldn't be suited to our indoor track I'm Very sad on that note !!! I really thought this would have been the next step UP |
#12
|
||||
|
||||
Quote:
|
#13
|
|||
|
|||
Quote:
__________________
ORCA - LC RACING - RUDDOG PRODUCTS - JCONCEPTS - ALPHA PLUS - TEKIN RACING - ULTRAPOWER AVID R/C - VAMPIRE RACING - EXOTEK RACING - LUNSFORD RACING - X-FACTORY - TUNING HAUS - WTF AME - RAGE R/C - REVOLUTION DESIGN RACING PRODUCTS - McKUNE DESIGN - TEAM AZARASHI X-PARTZ - PHAT BODIES - RACERS EDGE - RM2 - DIRT RACING PRODUCTS - DMS INSERTZ TKR GRAPHICS - BF MATERIALS - BATAN - DMS PARTZ - TEAM AJ Tel : (01923) 816636
|
#14
|
||||
|
||||
Please note in the video that Paul talks about testing various lengths. The U.K. Team generally liked +10, while the U.S. guys liked +8, so the compromise was +9. That certainly is not making it what is needed for dirt and "to heck with" U.K. conditions. You can't say that about some other companies.
http://xfactoryrc.com/rc/Videos.php |
#15
|
||||
|
||||
CHEERS guys for all yr replies !!!!
Now once again this forum has helped out with lots of my confusion 😉 I once again cannot wait til the x6 is finally released . Does anyone have an idea what sort of prices these bad boys wil be ??? |
#16
|
||||
|
||||
|
Thread Tools | |
Display Modes | |
|
|