|
#1
|
|||
|
|||
location
Does anyone no wher i can Put my novak speedo in a TAMIYA TRF 501X iv tried to put it where the motor is but the shell is not sitting down Where i want it. Its getting annoying if i remove th cooling fan the speedo gets worm so it ther for a reason any ideas
|
#2
|
||||
|
||||
are you running the worlds shell? that has more room for tall fans. Another option might be to run a low profile servo which might enable you to move the ESC a little for better fitment (thats what I've done)
|
#3
|
|||
|
|||
no it stanard the shell it so beutifull would u cut out in this bear in mind its my first pro painted shell
|
#4
|
||||
|
||||
Sorry I didn't read that, I put my ESC opposite the motor. I've not installed the Novak personally tho. The Worlds shell has more room but I managed to fit my Nosram with fan without toooooo many problems.
|
#5
|
|||
|
|||
so whats the best thing to do
|
#6
|
||||
|
||||
One of the people at my club has it installed behind the motor infront of the cells. I have my lrp sphere tc there too. It is tight but it does fit, then you have the motor tabs forward and the wires running flat across the top and soldered infront. This should give you a low enough profile to fit underneath the shell.
|
#7
|
|||
|
|||
could u sen a pic if its not to much so then i can get a breif idea
|
#8
|
||||
|
||||
Yeah sure, just taken these. No fan on the speedo cos im currently running indoors with a 10.5 limit and the speedo is barely warm without the fan.
You could probably have the motor further rotated forward but I was lazy and didnt want to rewire my speedo when putting the electrics in the 501. Hope this helps the guy with the gtb has it setup in the same place a few people have them setup on the opposite side as there is a bit more room but then you have the problem of routing wires over the car. Any more questions just ask. |
#9
|
|||
|
|||
thanks for the pics very nice
Last edited by vinny20; 23-05-2008 at 08:44 PM. Reason: dna |
#10
|
||||
|
||||
You can see what I mean about overhang - mine is rotated 90 degrees (and on the opposite side of the car) so it doesn't over hang.. mainly because I sometimes ran / run without undertray and didn't fancy hitting bricks with the esc
Will the fan fit under the shell there Mole? and which shell you running? |
#11
|
||||
|
||||
The fan does sit very close to the body (worlds edition) but it doesnt touch.
|
#12
|
||||
|
||||
MOLE2K - I have done the same thing with the same screws. Makes life so much easier doesnt it.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#13
|
|||
|
|||
i think i no what might be the problem when i switch it all on the speedo get worm but at the moment i have no radio so i think the speedo might needs reseting waht do guys think
|
#14
|
||||
|
||||
Quote:
Quote:
I considered for a while building a nerf bar to help protect the speedo but then I was too lazy to do that and i've only ran the car indoors so far. |
#15
|
||||
|
||||
This is how i did it!
with 5 cells in the car it gives you as close as possible 50/50 weight distribution in the rear
__________________
Daniel Persson Team Kyosho|Team Orion|AKA|DCD|GHEA Racing|Radiostyrt|Printhead|Nuclear-RC|bbqunltd|ToniSport|Spektrum |
#16
|
||||
|
||||
The Tekin R1-pro in my 501x "WCE" I didnt have location problems at all.
I didnt put it where you put that LRP Eraser which is another good small esc to put in this chassis, but I put mine right behind the servo. The cap on the Tekin R1-pro is also alot smaller than the Novak cap. Which I had alot of trouble getting my GTB to fit. The tekin and Lrp fit this chassis alot better. The car right above me is how I did mine, but my futaba fasst reciever is velcroed to other side of the servo. I also like the fact that the car above is useing the associated thumb screws. I used a complete B44 battery tray with the plastic battery hold downs. That is so I didnt have to file the chassis battery slots.
__________________
Associated B44, Tamiya 501x Worlds Edition Losi XX-4 finished project TRF 201(coming soon) |
|
|