|
#1
|
||||
|
||||
Mardave Adjustable ride height Alloy Pod
__________________
o0ple Trader Feedback NE Venue's New & Old my space on YouTube CFR RCTV Channel Glenn Atterton BRCA 2005 1/10th Off-Road Veterans Champion LMP12 National Champion 2003/2004 / F3 class |
#2
|
||||
|
||||
This is making my 'ideal' Mardave even more expensive!!!
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man! |
#3
|
|||
|
|||
just seen one in the flesh
very nice it is too |
#4
|
||||
|
||||
1/12th is a cheaper option at least for having a car ready to run than a fully spec'd mardave now. :0
|
#5
|
||||
|
||||
Tyres?
__________________
Mardave - RCbearings uk - Kamtec |
#6
|
||||
|
||||
Quote:
VRXce £90 Alloy Motor Pod £43 Carbon Chassis Kit £30 = £163
__________________
o0ple Trader Feedback NE Venue's New & Old my space on YouTube CFR RCTV Channel Glenn Atterton BRCA 2005 1/10th Off-Road Veterans Champion LMP12 National Champion 2003/2004 / F3 class |
#7
|
||||
|
||||
But a Mardave is more robust and cheaper to repair?
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man! |
#8
|
|||
|
|||
Agree with Karl 12th tyres are a lot more money than madaves, plus shells are cheaper and spares |
#9
|
||||
|
||||
new rear pod.
we have these on order !!!!! to go on my new CE car.
__________________
MARDAVE VRX CEC/REEDY/TEKIN/SANWA |
#10
|
||||
|
||||
Yes tires for 1/12th are alot more but I was just talking about the cost of the car by comparison.
|
#11
|
||||
|
||||
Rear pod
Just got mine today
__________________
MARDAVE VRX CEC/REEDY/TEKIN/SANWA |
#12
|
||||
|
||||
New Alloy rear pod
Hi Guys,
Just got these over the last week, once these was built up and installed into the car found that the rear axle would not turn we had to take off some of the Alloy on the pod just on the inside where the ride height inserts go!!! As the width of the whole assebelly seem just a tad to wide, Also had to shave off some of metal on the motor mounting holes as well as you cant seem to adjust the motor the get the correct mesh as the screws seems to bind when tightening them up!! Any one else had issues???? Dan.
__________________
MARDAVE VRX CEC/REEDY/TEKIN/SANWA |
#13
|
||||
|
||||
I have one of these pods nice bit of kit again like yourself the problem i to had was the motor adjustment bottom hole just a quick dremmell and all was good shaved a little bit off the Z drive all good raced with it friday at ardent well impressed nice bit of kit well done Chris
|
#14
|
|||
|
|||
I've had the same issues with the gear mesh holes on plastic pods.
|
#15
|
||||
|
||||
quote from Team Mardave on FB
Quote:
__________________
o0ple Trader Feedback NE Venue's New & Old my space on YouTube CFR RCTV Channel Glenn Atterton BRCA 2005 1/10th Off-Road Veterans Champion LMP12 National Champion 2003/2004 / F3 class |
|
|