|
#21
|
||||
|
||||
Quote:
Cheers
__________________
AKA Dexter Ex Club Chairman Visit our Face Book Page for address and to book in https://www.facebook.com/groups/289589121226171/ http://www.neamotorsport.co.uk/ |
#22
|
|||
|
|||
If the cartridges are cheap and not just the printer then do it.
|
#23
|
|||
|
|||
I thought our printer is pretty new.....for once I thought we were all sorted in the electrical department??
When's the AGM aswell? |
#24
|
|||
|
|||
I'll speak to Ian but ideally the weekend after this round of Worksop.
|
#25
|
||||
|
||||
guy's I would recommend 12mm ply for the face of the jumps and any table tops as anything less and you'd run the risk off people putting there feet through it when marshalling, plus would add strength too so wouldn't need as much 2x2
You could use thinner ply on the sides and buy rough sawn 2x2 which would be cheaper than dressed timber Just and idea, I also have a trade point card for b&q so would save 10% off price and you'd get the board cut for free if you have the sizes you need
__________________
Jason Robinson ---------------------------- Tekno EB410 Associated B6.1 |
#26
|
||||
|
||||
I would be willing to help clear out/reorganize the garage I think there is quite a bit of space available in there as is
but there is allot of gear that doesn't seen to be used on a weekly basis i'm free most days and weekends just let me know when I can help |
#27
|
|||
|
|||
Quote:
Thanks to everyone for the offers of help you are one of the main reasons why we're the best club in the North East. We'll get the AGM out of the way and the following week get there early whist the bands using the hall we can have a tidy up in the garage. |
#28
|
||||
|
||||
No problems its my job so if you need any boards or out cutting let me know and can bring big flip saw up
also if you want to borrow my discount card your more than welcome, I can give to you sunday just let me know
__________________
Jason Robinson ---------------------------- Tekno EB410 Associated B6.1 |
#29
|
|||
|
|||
Just an idea, see if you can work out the geometry for some folding ramps.
I did some rough sketches last winter, as our track is shared with the tc guys and we have limited storage storage, but it didn't go any further than sketches! Just the bigger ones, as that's where you can save the most space. |
#30
|
||||
|
||||
Quote:
I have been out and got some 2x2 and some 2x1, but I haven't got any ply yet. It's maybe a little more ££s than I expected, so I would like the go ahead before I spend .... I will see the lads @ Worksop tomo . Very good of you to lend us you discount Jason but I find B and Q to be very expensive eg a treated 2x1 x 2.4m in B and Q is £3.12, the same in a local ish builders yard is £1.20. Even with discount it would have been expensive! Quote:
|
#31
|
||||
|
||||
Quote:
Is they anyway we can check with the band that it will be ok to go in the garage early? I know it wouldn't be a problem but we don't really want to upset them as they usuall let me in abit early and start getting the track out even when they haven't finished |
#32
|
||||
|
||||
Quote:
Will also try to find out from the youth centre if there is anything that needs keeping or taking over to the skips
__________________
AKA Dexter Ex Club Chairman Visit our Face Book Page for address and to book in https://www.facebook.com/groups/289589121226171/ http://www.neamotorsport.co.uk/ |
#33
|
||||
|
||||
Good work Dex, I know it wouldn't be a problem but best to ask to keep things sweet
|
#34
|
||||
|
||||
Hi Andy, no probs mate just thought i'd put the offer out as I tend to find they expensive for some bits and cheap for others
But if you do need any help be it cutting or getting bits just let me know
__________________
Jason Robinson ---------------------------- Tekno EB410 Associated B6.1 |
#35
|
||||
|
||||
Quote:
I'm not sure how it will pan out but if we end up going to the club early a week on Sunday it would be good if you could bring a drill/driver and help assemble some of the bits I hopefully get made of your available of course |
#36
|
||||
|
||||
sure Andy I'll bring some with me
__________________
Jason Robinson ---------------------------- Tekno EB410 Associated B6.1 |
#37
|
||||
|
||||
Update
Well I managed to get some bits put together, I was running out of day light so the pics are abit rubbish but you get the idea
A few finishing touches to do but, I don't think they will be much stopping us using them tomo night |
#38
|
|||
|
|||
That is mental, it looks huge and I love it. Cheers for building it Andy.
|
#39
|
||||
|
||||
Nice one andy
__________________
'There are two choices in life-Take it or leave it !' Yokomo - Nemoracing Sb Designs http://www.fairfueluk.com/ |
#40
|
||||
|
||||
Yeah it's a fair size .... It took most of my drive up !!! I'm a lilttle worried about the 'up' ramp being a little steep, I think it does look steep in the pic, only thing to do I guess it to give it a try if it's no good it can be altered in time
|
|
|