|
#21
|
||||
|
||||
With the Interclub coming up at Batley next month wondered if anyone had a good setup they'd be willing to share!!
Looks like NERCR will be able to put at least one team together!! Last edited by notlawnomis; 04-08-2006 at 10:03 AM. |
#22
|
||||
|
||||
i have sent a set up to jimmy for what i ended up on at the batley national so euros allowing it will be up soon or pm me a email addy and i shall forward you a set up sheet for the track.
Thanks Nathan Quote:
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams woop woop racing officialy keeping team toe out inline |
#24
|
|||
|
|||
anyone here got a general setup for dusty dirt tracks?? i'm looking for something from mark pavidas but cant find any
|
#25
|
||||
|
||||
if you go to 4wdrc.com there is a kyosho section there and pavidas's setup from the cactus classic is in there somewhere
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams woop woop racing officialy keeping team toe out inline |
#26
|
|||
|
|||
Setup from the Euro in Vienna
Does anybody know the best Setup from the European Championship in Vienna at the RMC-Track?
|
#27
|
||||
|
||||
having just done the euros last week i shall be posting a setup soon for the vienna track
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams woop woop racing officialy keeping team toe out inline |
#28
|
|||
|
|||
hi guys. just building my first zx-5.
the manual says put spacer in the front of each of the bulkhead (under D plate for the front and BR plate) but it doesnt say anything about putting a spacer under the rear toe plate (A30), and also behind the front bulkhead (under C plate) do you put spacers there? coz i seen some setup sheets it specifies to but plates there. thanks |
#29
|
|||
|
|||
Hello all,
I have my Lazer since a couple of weeks. Watching the Lazer category in this forum I found many ideas and good hints. I just tried setting up my ZX5 like the Batley sheet. Some general questions for the setup sheets figured out here: (Maybe because I could not interpret the english name for the parts in the right way) - Front and rear suspension 'Upper Spacer': Is it an optional part or is it in the kit? Where to find, which itemnumber? - Axle Hight Spacer: What is meant by UP or LOW? Is the UP position with the spacer on the bootom? - Hub Carrier back: How to set up the hub carrier to 2°? Is it an option part or just put the screw to another hole? - long wheel base on rear hub: What to do here? Is there an general description for the setup sheet and for the effects using option parts? Please help me a little here. thanks Andreas Last edited by andreasH; 02-09-2006 at 06:06 PM. |
#30
|
|||
|
|||
thanks to jimmy for his review and suggesting to use short camber links front and rear. it made the buggy so much easier to driver and less twitchy.
this always went against what i thought those links was supposed to do. i always thought a longer links gave more stability, and better for loose tracks. |
#31
|
|||
|
|||
Quote:
I need a working setup for very low traction. Someone who can help me here?
__________________
regards Andreas ----------------------------------------------- BJ4 WE; Durga; Dark Impact ;TT-01 |
#32
|
||||
|
||||
Well, I have run the car on slippy gym floors a couple of times (pretty low traction), and found that basically the kit setup minus rear anti-roll bar, with a diff up front, centre one-way (locked if the track is REALLY slippy) worked just fine, maybe a slight lack of steering on-power.
Pretty basic I know but it might be a starting point. |
#33
|
|||
|
|||
Thanks. I run the front diff and center locked. Steering could be better.
The car of a friend has the KMC conversion and runs much better here. The track is clay/loam and is absolut glibbery. I run Proline Hole Shot, which tires would be good here? So I will test without the anti-roll bar. Would an anti-roll bar in front be good here?
__________________
regards Andreas ----------------------------------------------- BJ4 WE; Durga; Dark Impact ;TT-01 |
#34
|
||||
|
||||
No harm in trying a front anti-roll bar, however it is more likely to reduce steering than create it. Personally speaking I don't really like anti-roll bars as they make the car a bit fidgety over the bumps.
All you can do is try these things! |
#35
|
||||
|
||||
losi springs
i run losi silver front springs and pink rear spring the car was loads better this on wet astro so it was slippy like clay and it jumped a load betteri n fact u could push it thats a first for a lazer also run 50 wt oil in the front with big pistons
__________________
who knows who cares |
#36
|
|||
|
|||
I will try some changes tomorrow on our last clubrace.
__________________
regards Andreas ----------------------------------------------- BJ4 WE; Durga; Dark Impact ;TT-01 |
#37
|
|||
|
|||
The weather was very bad this weekend so our race was canceled.
The Buggy season is over for this year, now we go for indoor onroad. The club is doing an modification of the track in the next weeks. Hopefully they change the road surface to get more grip otherwise i have to work very hard on an working setup next season. (now waiting for christmas to get some new parts, maybe the conversion kit)
__________________
regards Andreas ----------------------------------------------- BJ4 WE; Durga; Dark Impact ;TT-01 |
#38
|
||||
|
||||
upper spacers are just a standard 1mm thick washer so 2 of those to raise the ball stud to stiffen it up the roll a little
up position is with the washer below the front hub 2 dgree hubs are an option part (sorry dont know the number) long wheel base on the hub is to put all the hub spacer washers in front of the hub to push it backwards as far as possible hope this helps. sorry for the delay in answering your questions but i dont get the chance to look on here very often Quote:
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams woop woop racing officialy keeping team toe out inline |
#39
|
|||
|
|||
9 months delay?
|
#40
|
||||
|
||||
but still answered :S :S
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams woop woop racing officialy keeping team toe out inline |
|
|