|
#21
|
||||
|
||||
posted twice
__________________
Team X-Tream X11 08 spec Schumacher MI4 lp: Tekin rs pro speed passion V3 10.5 |
#22
|
||||
|
||||
Quote:
thanks
__________________
Team X-Tream X11 08 spec Schumacher MI4 lp: Tekin rs pro speed passion V3 10.5 |
#23
|
|||
|
|||
gearing etc.......
Hi guys
what spur gear comes with the kit there are 4 differant ones on the parts listings but carn't seem to find what it has actually come with without counting the teeth same with the idler gear too also recommened gearing for a 6.5 and 5.5 with nimh batterys pleeeeease thanks paul |
#24
|
||||
|
||||
83t is the kit
__________________
Team X-Tream X11 08 spec Schumacher MI4 lp: Tekin rs pro speed passion V3 10.5 |
#25
|
|||
|
|||
Set-up for the Dirt (with LIPO)
Si,
Could suggest a set-up for the dirt, with a LIPO pack? Seeing as it is lighter, one would probably only need to adjust the shock collars for the ride height? Would lighter oils also be necessary? What has your testing revealed? Thanks again. Last edited by garystyger; 26-09-2008 at 08:58 AM. Reason: Spelling |
#26
|
||||
|
||||
We run on 8th scale buggy tracks so our cars are consistently jumping 20-30 feet in the air and I have the LiPo version running 35wt in the rear and 40wt in the front. I haven't run it yet but I will tonight and I've seen the side to side weight bias is very nice with the LiPo.
Also last weekend I was running 35wt front and rear and it was a bit to soft in the front |
#27
|
|||
|
|||
i will try and post a set-up for "american style" tracks.........we use losi pink tapers ground down to slicks
car looks amazing!!!! has anyone tried losi or ae wheels in the rear????
__________________
schumacher www.racing-cars.com core lipos www.racing-cars.com speeed passion www.speedpassion.net airtronics www.airtronics.net checkered flag raceway www.cfrkc.com Lipo sack www.liposack.com |
#28
|
||||
|
||||
I've not tried yet, but would normal hex's fit on it?
I've got a cart load of HB wheels, so wondered if they'd fit? |
#29
|
|||
|
|||
last night i put hexes from b44 on the front
jconcepts wheels bolt right up..........man this looks killer
__________________
schumacher www.racing-cars.com core lipos www.racing-cars.com speeed passion www.speedpassion.net airtronics www.airtronics.net checkered flag raceway www.cfrkc.com Lipo sack www.liposack.com |
#30
|
|||
|
|||
Here is the setup i finished up on at Worksop.
Front - Track Washers - 1mm front and back Roll Bar - No Shock Position Mount - Middle Shock Position Wishbone - Middle Front Rake - 10 Degrees Washers - 3mm Front Link Bracket - 43mm Washers on Hub - 0 Rear - Wheel Base - Short Toe In - 3mm Rear, .5mm front = 3.25 degrees Anti Squat Washers - 2mm Rear, 1mm Front = 1.3 degrees Rear Link Bracket - 37.5mm Washers - 4mm Shock Position Mount - Middle Shock Position Wishbone - Inside Hub Postion - Middle Roll Bar - No Shocks Front - 30wt on 3 Holes Schumacher Red Springs (Old) Diaphragm - Centre cut out and removed Ride Height – Drive shafts level Rear - 25wt on 3 Holes Schumacher Yellow Springs (New) Diaphragm - Centre cut out and removed Ride Height – Drive shafts level. Transmission- Rear Diff Height - Low Front Diff Height - Low Layshaft Pulley - Pin Through Front Drive – One Way Gearing - 83 x 24 on Speed Passion 5.5 Internal Ratio - 36 Tooth Pulley Thanks Si
__________________
Schumacher, Hobby Wing, Thunder Power, Anderson, Sanwa, Trishbits, P-Dub Racing, Rudebits, Inside Line, Nuclear RC, RC Domination, RPC |
#31
|
|||
|
|||
Thanks for the setup Si but I have a few questions:-
What is the 36T pulley mentioned in the internal ratio section? I only see a 34T pulley being the largest size to get the 2.8 internal ratio. Do you run the ackerman bar with 8mm between the ball cups as per the manual? Also the front link bracket you say is 43mm I presume this could be a prototype part as according to the Turnbuckle length guide this is now supplied as U3442 38.5mm rather than 43mm as stated in the manual. The Worksop report says you ran the 6.5 motor, did you change to the 5.5 for the final? |
#32
|
||||
|
||||
What difference does it make by running the height of the diffs low or high?
__________________
Associated SC10. Associated RC8. Atomic Carbon S4. Paint by Wezzer. |
#33
|
||||
|
||||
Looking for a set up for indoor shiny wood surface.
__________________
Associated SC10. Associated RC8. Atomic Carbon S4. Paint by Wezzer. |
#34
|
|||
|
|||
I can recommend the setup from above with Schumacher mini pins and medium foams. I ran this setup on Friday which was a mixture of polished floor and some carpet and it ran very well, much better than my initial setup that I ran which was waaaay off
__________________
Schumacher KC, KD, CAT XLS, CAT L1 | Team C TM2 V2, TM4, TC02 | JQ The Car | Mugen MBX6 | Losi 8T,8BE 1.5 | Durango DEX-410V4 | FTX Blaze | XRAY M18T | Kyosho STR,Surf Dude,Nexus 30 | Nimrif Makara | MFA Spear | She Devil | T-Rex 450SEV2,250SE | Ark X-400 | Protech Butterfly,Zoom 400 | Ikarus Piccolo | VW T4 | Smart 450 | KC-250 | BoltRC Kraken 5" | Emax Nighthawk 250 | Gravity 250 | S550 | Prusa i3 | TronXY X5A | Must stop collecting stuff! |
#35
|
||||
|
||||
Is Mossy's setup from above with Lipo or NIMH and if with Lipo was there any weight added?
My car is 1602gr with lipo and no added weight and to be honest it seems just fine and dandy but would still be interesting to know |
#36
|
|||
|
|||
Lipo, no weight added.
Si
__________________
Schumacher, Hobby Wing, Thunder Power, Anderson, Sanwa, Trishbits, P-Dub Racing, Rudebits, Inside Line, Nuclear RC, RC Domination, RPC |
#37
|
||||
|
||||
I finally found a Freeware program that allows to open, edit and save PDF's.
Only downside is that it will make some mistakes in the graphics( At the Cat SX setup it won't show the blue parts)so you will have to edit a prefilled setup to know what you are writing. Opened in Adobe reader everything is then shown in full beauty. Link:http://www.cib.de/deutsch/products/p...-speichern.asp Cruise.
__________________
Team CS-Electronic Team Schumacher |
#38
|
||||
|
||||
Thanks Si
|
#39
|
|||
|
|||
search cat sx carpet set up
hello,
I hope you can help me: I search a good cat sx lipo version' s set up for race on full carpet trak with rubber tyres (schum yellow mini pin). Verry great thanks for your answer and sorry for not verry good english (I leave in belgium and i speak french and a little english) Best regards. |
#40
|
||||
|
||||
Mossy, on your worksop setup above there's no mention of toe-in and camber settings. what are you running with ?
__________________
Stevie Brew BW-RACING@HOTMAIL.COM http://www.oople.com/forums/showthre...hlight=stegger |
|
|