|
#4001
|
||||
|
||||
Didnt realise Rick made third, still I recal his Lazer from the Reedy event and his Ujs were stunning. If only they made silver like his it would have been ace. Also dont forget there a video of him kicking Masamis but when he had the YZ10 with his nicely handling ZXR.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#4002
|
||||
|
||||
Here it is.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#4003
|
||||
|
||||
Thanks welsh
here is an shoot at Jack when he beat masami and lett. http://www.youtube.com/watch?v=Ob42CpxWIAA mvh sobarik |
#4004
|
|||
|
|||
Quote:
Thanks for the link iso, really enjoyed watching that |
#4005
|
||||
|
||||
Yeah its an nice vid , but damn that track was very bumpy.
When i looked at the 3rd vid i noticed that joel was fourth. since pixbox is down and it was there i had my pics so what shall i go for photobucket maybe ??? i have an piece that i would like to show mvh Isobarik |
#4006
|
|||
|
|||
Quote:
I tend to use Flickr but I think photobucket is good also. |
#4007
|
||||
|
||||
Well when i raced seriously i always preferred sanwa gemini exerd for my transmitter, and by chance acquired one recently, now to upgrade it to 2.4ghz. Ive also acquired a ko propo typr r and has been upgraded to 2.4 ghz, so decisions decisions, which do i use with my Lazer?
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#4008
|
||||
|
||||
Quote:
mvh Isobarik |
#4009
|
||||
|
||||
Welsh
Thanks for the pivot holder, have modified it a little bit and sent it to fibre-lyte . if my measuremnts are correct the differance in distance between the 1,5 bracket and the 2.o bracket for the zxs are 1,6 mm if i would like to have an 3 degree bracket shall i just add 3,2 mm or am I compleatly off here ??? mvh Isobarik |
#4010
|
||||
|
||||
Oli4ke
ihave the parts that you wanted pm me . mvh isobarik |
#4011
|
||||
|
||||
Nope it because your ladies love to work my shaft
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#4012
|
||||
|
||||
Well njaee i still think that you like to work the shaft ... how about the bracket degree ??? i would like to have an 3 degree toein bracket . mvh Isobarik |
#4013
|
||||
|
||||
I remember back in the day I preferred stick to wheel controllers and that hasn't changed
__________________
___________________ Maxxum FF Ultima Pro Turbo Optima Mid SE Turbo Optima Mid SP Optima Mid Custom Special Lazer ZX Lazer ZX-R Lazer ZX-S |
#4014
|
||||
|
||||
Quote:
I did a lot of testing in the early 90's to better the overall performance and found the front didnt really need much changing other than the wide front and more castor plus the ZX steering lonkage. The back however was a different affair. I tried reversing wishbones, front wishbones, many hubs, toe in, out etc etc and found the toe in or out on the rear was good, narrower rear hubs (fractional) from the Ultima RB type R (I had most probably the only one in the UK) gave significant options to ride height and made the rear end more responsive due to the narrower width of the car, shock towers and angle of the shocks as well as tie rod adjustment angles and roll bars. I also did try lower pivot blocks on the front and rear and also preferred it on the lower original setting, but I did also try upside down on occassion as this gave a change on some tracks. If you want an angle sideways just put toe out on the front
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#4015
|
||||
|
||||
Quote:
Also when do we see your pics on here of your new toy?
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#4016
|
||||
|
||||
Quote:
mvh Isobarik |
#4017
|
||||
|
||||
So those drawings i did were for the front as thats what i thought you wanted. Still 3 on the back should be fine.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#4018
|
||||
|
||||
Quote:
So i was glad that you gave me the drawing on the front bracket and i have sent it to fibre-lyte to have it made. But when i was looking on their site i just whised that i had an 3 degree bracket in the rear. WSo thats why i asked you about it. So what shall be the distance between the two holes so that its 3 degree instead of 2degree ??? mvh isobarik |
#4019
|
||||
|
||||
Unsure but you have a zxs and the rears are various degrees so should give you an idea
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#4020
|
||||
|
||||
Quote:
I've put a few pics up in a new thread
__________________
___________________ Maxxum FF Ultima Pro Turbo Optima Mid SE Turbo Optima Mid SP Optima Mid Custom Special Lazer ZX Lazer ZX-R Lazer ZX-S |
|
|