|
#421
|
||||
|
||||
I tired the idler gear where you have yours simon and it meshes with the spur first Need to investigate more me thinks.
A
__________________
Ashley Williams I always thought by 2013 we would have flying cars, but we have got blankets with sleeves! |
#422
|
||||
|
||||
It is a bit noisy for about 10 minutes of driving, after that the car has the same noise as any other car.
|
#423
|
||||
|
||||
Thanks guys.
__________________
Schumacher KF | K1 Aero | RWS RZ6R |MiniZ MR-03 | Orion R10 esc | LRP motors | Orion 90c lipos Rusti Design - Awesome custom stickers and cool stuff My trader feedback |
#424
|
||||
|
||||
Hard, isn't it?
__________________
|
#425
|
||||
|
||||
Hydra drive
http://img43.imageshack.us/i/015fu.jpg/
-is this some old stuff? Not std. on the XXX-CR? Better than a std. slipper???
__________________
Life's too short to go slow! www.ymr.no Tech Tips, HopUps & Bling Xray 2014 XB4 4WD & 2WD | B4 FTW Night Fox XL | Mugen MRX-5 | RB | Futaba 3VCS FASST | Faskolor Visit my showroom |
#426
|
||||
|
||||
Whats the difference between the hydra drive and a normal slipper?
__________________
|
#427
|
||||
|
||||
hydra drive has a impeller inside(kinda like a propeller) that runs between veins inside the caseing and uses oil and the impeller as the slipper element,its a fluid(oil)drive/slipper
__________________
Mattys the driver,my names carl
|
#428
|
|||
|
|||
Jono, come see me thursday, i can show you the inside of one. Not sure if I will use it yet though
|
#429
|
||||
|
||||
Well i sucseeded on doing the idler gear mod like si. Only issue i had was at full suspension travel my wishbone rubs on the idler gear. So im going to put 1 external spacer to stop and ive removed the edge of the idler gear by putting the car to half throttle and using a file
A
__________________
Ashley Williams I always thought by 2013 we would have flying cars, but we have got blankets with sleeves! |
#430
|
||||
|
||||
Looks like you've done a cracking job with that car Ash, In every picture ive seen it looks spot on
__________________
|
#431
|
||||
|
||||
Cheers garry
Had a few problems ive ironned out its a bit dirty at the momment. But im sure it will get alot dirtier at the weekend. A
__________________
Ashley Williams I always thought by 2013 we would have flying cars, but we have got blankets with sleeves! |
#432
|
||||
|
||||
Just put the new Rudebits front corner weights, rear side pod weights, under motor weight and battery bars on the car along with Simons roll bar ideas and will run it on Wednesday at Bicester. I'll post the results on Thursday.
Thanks to Tony at Rudebits for the parts, I have to say they are as always a PERFECT fit to the car and they look amazing. I know from watching Simons car at the weekend that they really improve the handling of the car so i'm looking forward to giving them a go. Get Rude .............. you know it makes sense |
#433
|
|||
|
|||
Ashley
I had the same problem with the Idler being to close to the wishbone at full suspension compression so if you look at my pics in detail you will see i have removed a small amount of the front wishbone just with a dremel. Just means the wishbone now does not hit the idler but make sure you us a spacer on the rear of the hinge pin so that the hinge pin has no slop and can't hit the idler. Hope that helps Si
__________________
Si Reeves - Herts Rc models - Schumacher - Beta - Spektrum - Rudebits.co.uk - SMD - Insideline Racing |
#434
|
||||
|
||||
Information on hydra drive for those who dont know about it....
http://www.vintagelosi.com/More_files/hydratech2_1.jpg A
__________________
Ashley Williams I always thought by 2013 we would have flying cars, but we have got blankets with sleeves! |
#435
|
|||
|
|||
Quote:
__________________
ORCA - LC RACING - RUDDOG PRODUCTS - JCONCEPTS - ALPHA PLUS - TEKIN RACING - ULTRAPOWER AVID R/C - VAMPIRE RACING - EXOTEK RACING - LUNSFORD RACING - X-FACTORY - TUNING HAUS - WTF AME - RAGE R/C - REVOLUTION DESIGN RACING PRODUCTS - McKUNE DESIGN - TEAM AZARASHI X-PARTZ - PHAT BODIES - RACERS EDGE - RM2 - DIRT RACING PRODUCTS - DMS INSERTZ TKR GRAPHICS - BF MATERIALS - BATAN - DMS PARTZ - TEAM AJ Tel : (01923) 816636
|
#436
|
||||
|
||||
Quote:
__________________
|
#437
|
||||
|
||||
Dremel's an excellent tool ............... and should be included in the price of some "other brand" kits
|
#438
|
||||
|
||||
are the hydras still commercially avaliable? or is it a case of rocking horse shit?
|
#439
|
||||
|
||||
Ask Darren at DMS, i'm sure he'll be your best bet
|
#440
|
||||
|
||||
Quote:
Reevsey bought the last one dms had in stock so it's down to horizon now not sure if they will still carry any.
__________________
|
|
|