|
#62
|
|||
|
|||
Quote:
|
#63
|
||||
|
||||
Yep sorry already corrected. The really embarrassing thing is I didn’t notice the mistake when I done it last night.
It was only when I was moving the wishbones up and down to test shocks that I noticed a massive change in camber, then in reverse spotted the issue. How silly. The plate with the ball-studs is screwed on separately, so in my tiredness at 1am I must have made it then. Anyway don’t worry - the photos I am sorting through now are all back to normal. I was kinda hoping no-one would spot the error hehe... |
#64
|
||||
|
||||
I have put Trakpower in my SX, 3200's and 3600's fit fine. Let me know (PM if you want) and i'll show you what I have done etc.
|
#65
|
||||
|
||||
Quote:
I'd certainly like to see your solution Chris if you wouldn't mind. Thanks p.s. only my last photo in my previous collection now has me silly mistake :-) |
#66
|
||||
|
||||
Ive got a 4900 in mine, it does fit - connectors to the rear, it is a bit tight though but i'll still be running it at worksop..
|
#67
|
||||
|
||||
As for spares, haven't really broken much, but obviously depends how hard you want to hit stuff!
Did some front arms early on, but haven't done one in ages, same for front and rear hubs - but they have both been changed since then. Haven't ever done either shock towers!! Worth keeping the usual suspects in though, as well as some screws for the pin mounts, i have bent a couple of these.
__________________
Matthew White |
#68
|
||||
|
||||
Quote:
Bet I get mine built before yours
__________________
KECKSpeed - Seat of your Pants R/C Racing www.keckspeed.co.uk ryan@keckspeed.co.uk |
#69
|
||||
|
||||
OMG it lives, see you managed to find the power button on your PC
That's it i'm getting down to the shop now Stil gone for the Lipo version fella ?
__________________
Stevie Brew BW-RACING@HOTMAIL.COM http://www.oople.com/forums/showthre...hlight=stegger |
#70
|
||||
|
||||
Well blow me down, i thought you were dead, well thats the rumour i started anyway
|
#71
|
||||
|
||||
Too Right....Lipo's the Future
Just don't mention it when you pick yours up
__________________
KECKSpeed - Seat of your Pants R/C Racing www.keckspeed.co.uk ryan@keckspeed.co.uk |
#72
|
||||
|
||||
You Wish, i'm like a bad smell me, always showing up when you least expect it
__________________
KECKSpeed - Seat of your Pants R/C Racing www.keckspeed.co.uk ryan@keckspeed.co.uk |
#73
|
||||
|
||||
No worries fella
__________________
Stevie Brew BW-RACING@HOTMAIL.COM http://www.oople.com/forums/showthre...hlight=stegger |
#74
|
||||
|
||||
So which Lipo batteries will fit without any form of modification?
Manufacturer, mah rating etc?
__________________
KECKSpeed - Seat of your Pants R/C Racing www.keckspeed.co.uk ryan@keckspeed.co.uk |
#75
|
||||
|
||||
depends which chassis you buy
But in the lipo chassis i know the 3200 and 3600 Trakpowers fit |
#76
|
||||
|
||||
Hi Glypo, Ive sent you a PM. if you let me know your email address i will send a picture of my Trakpower in SX.
What I have done is, like James says, plugs to the rear. The positive goes right in, to the centre of the car. But if you tie wrap the positive wire to the underside of the topdeck, about 2inches infront of the plug, with same amount of slack on the wire - it can be plugged in with the cells out slightly, and then slid back. The belt will be around 5mm away from the wire. The negative just goes straight through the belt, ive tie wrapped it with the positive when I tooked that up, and it stays away from the belt by miles. I can send any photos, but im not so good at hosting and posting them here. If anybody needs photos to clarify what I mean, just drop me a PM. Chris |
#77
|
||||
|
||||
The NiCad Version
__________________
KECKSpeed - Seat of your Pants R/C Racing www.keckspeed.co.uk ryan@keckspeed.co.uk |
#78
|
||||
|
||||
|
#79
|
||||
|
||||
Chris forgive him, he's been away for a while
__________________
Stevie Brew BW-RACING@HOTMAIL.COM http://www.oople.com/forums/showthre...hlight=stegger |
#80
|
|||
|
|||
this looks so good
|
|
|