|
#1701
|
||||
|
||||
Ok,
Steve does the hotwire recognize the esc? If it does, try re updating your software. DO NOT interrupt it.
__________________
Tekin Team Manager |
#1702
|
||||
|
||||
I recently updated to 223 so that may have something to do with it. I'll try and get back to you.
Cheers Steve |
#1703
|
||||
|
||||
Thanks for all the assistance Randy, software downloaded again and all appears to be running well again.
Top Tekin Service!!! Steve |
#1704
|
||||
|
||||
Nice!
__________________
Tekin Team Manager |
#1705
|
||||
|
||||
Hi Randy, I gave the tekin rsx a run out this weekend with 5.5 gen2 motor.
Ive checked logs after and notice motor topping out at around 32k rpm. temps were great. Is this rpm value normal? MMotor end timing is at 0 deg. Thanks. |
#1706
|
|||
|
|||
Any timing yet for when there will be gen 1 support on hotwire 2.0?
I've seen that they will be supporting on the tekin forums, but no real timing, just "soon". |
#1707
|
||||
|
||||
32k in 4wd buggy is pretty normal. Gearing is what really controls that figure. Look at the throttle input rpm "bell" curve and see if it's the flat topping. Take a read here and see this helps:
http://www.teamtekin.com/manuals/TWS...wTo_111513.pdf Explains a few things to look at and what changes to make.
__________________
Tekin Team Manager |
#1708
|
||||
|
||||
The next App update will provide Gen1 support. It also corrects the 4.2+ android OS issues.
__________________
Tekin Team Manager |
#1709
|
|||
|
|||
Nice. Just have to sit here and twiddle my thumbs until then!
|
#1710
|
|||
|
|||
Hi Randy
What is the recommendation on here, in using the current limiter on tekin rs pro on a 7.5 turn motor. For racing 2wd buggy on a indoor slippy wooden floor/carpet circuit. I just want to smooth the low end out as at the moment the tiniest throttle input will over load the tyres when accelerating out of corners on the wooden floor. I am aiming for the top end of a 7.5 but the acceleration of a 10.5. Thanks |
#1711
|
|||
|
|||
Quote:
__________________
[CENTER]TKRrc[/CENTER[/URL]] |
#1712
|
|||
|
|||
Slipper clutch won't help on wooden floors, as the path of least friction is the rubber and the floor. I am currently using a futaba 3pk. I am going to set the throttle current limit to 55 to see how that goes and set the throttle profile to 1.
|
#1713
|
||||
|
||||
I use same radio and did have same ESC bud. I set an expo on throttle between 25 and 45. it really smoothed out the bottom end
|
#1714
|
||||
|
||||
Quote:
If you watched my car today, i was running a boosted 17.5T with some extra timing with a slight delay for the straight. The car was super drivable and i hardly made any mistakes. i could have used a bit more speed, so next time I'm trying a 13.5T.
__________________
-------------------------------------------------------------------------------------------------------------------
Team Yokomo - YZ-2CAL3 | YZ-2DTM3 | YZ-4SF2 | YZ-2T | YZ-2DTM Worlds | YZ-2DTM x2 | YRX-12 x2 ------------------------------------------------------------------------------------------------------------------- 10electric | Batley Buggy Club | YORCC | RHR | MB Models --------------------------------------------------------------------------------------------------------------- |
#1715
|
|||
|
|||
negative or positive expo ?I don't want to buy a new motor before racing outdoors.
|
#1716
|
||||
|
||||
Sounds like you may be boosting a 7.5 or have an odd setup here.
First off you shouldn't need to boost a 7.5 in a 2wd buggy. It's already going to have a lot of power. Anytime i'm on a slick surface with a motor/setup where I want 10.5 acceleration but 7.5 top end i go to dual mode. Dual mode with timing set to 20(Gen2) or 80(Gen1 esc) which will make it butter smooth but still have "legs" on top.
__________________
Tekin Team Manager |
#1717
|
||||
|
||||
Quote:
-25 mine was at Sunday, as grip was pretty low and my motor/esc combo is an animal its also set with the minimum throttle expo profile on the esc. Cant remember which of top of my head, but you'll find it in the hotwire settings. RSX+5.5 gen2, loving it. |
#1718
|
|||
|
|||
Quote:
Got version 2 of the software, I am right to assume the 20 is equal to 80 when using dual mode? Danny what neutral width do you use for the throttle setting on the RS pro? |
#1719
|
||||
|
||||
On RS PRo the Dual mode is a percentage of 30 degrees. So 80 percent is 20 degrees.
__________________
Tekin Team Manager |
#1720
|
|||
|
|||
Thanks Randy. I am oil and gas engineer, we don't like to make assumptions dealing with 15,000 psi.
|
|
|