|
|
#1
|
||||
|
||||
S-Workz S12-1M setup's
I found this link on petit with the worlds setup
http://site.petitrc.com/setup/sworkz...WorkzS102.html
__________________
Answer RC team driver Formby models HB Racing D216 HB Racing D418 www.kandmacoustics.co.uk |
#2
|
||||
|
||||
Setup sheet was also highly revamped.
|
#3
|
||||
|
||||
worlds setup is also in the manual
__________________
Stephen Smith Answer RC Team HB Racing | Team Orion | Xpert | Racing Experience |
#4
|
||||
|
||||
Southport turf wars r4 setup
This is my setup i ran at southport today, the track is two different types of astro on an indoor track
__________________
Answer RC team driver Formby models HB Racing D216 HB Racing D418 www.kandmacoustics.co.uk |
#5
|
||||
|
||||
Lee check your Facebook messenger. I've sent you the link for your final yesterday
__________________
PR Insidelinemodels |
#6
|
||||
|
||||
Guys, any idea what teeth are on the diff gear on this car, is it 55? Ok just worked out its not 55.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS Last edited by Welshy40; 13-02-2016 at 08:50 PM. |
#7
|
||||
|
||||
not sure, time to get the tipex and start counting lol
__________________
Stephen Smith Answer RC Team HB Racing | Team Orion | Xpert | Racing Experience |
#8
|
||||
|
||||
Southport Easter egg race Wet Conditions
this is my setup fron the weekend at srcc
__________________
Answer RC team driver Formby models HB Racing D216 HB Racing D418 www.kandmacoustics.co.uk |
#9
|
||||
|
||||
This is the setup i ran at bury on the 10th april track was damp at start of the day bur dried out near end of day
__________________
Answer RC team driver Formby models HB Racing D216 HB Racing D418 www.kandmacoustics.co.uk |
#10
|
|||
|
|||
i saw you setup with rb6 ball diff so i got one to install. was not the easiest to put in but how did you get it in?
|
#11
|
||||
|
||||
Dremel the outdrives
__________________
PR Insidelinemodels |
#12
|
||||
|
||||
As Paul said you need to dremel the out drives and use about 4mm of shim a each side
__________________
Answer RC team driver Formby models HB Racing D216 HB Racing D418 www.kandmacoustics.co.uk |
#13
|
|||
|
|||
i got it to work but i actually used vinyl tubing that had the same id as the od of outdrives and works perfectly. tube cost $.50 for 1'. car does awsome on clay with ball diff.
|
#14
|
||||
|
||||
This is my setup from batley. Low grip very bumpy
__________________
Answer RC team driver Formby models HB Racing D216 HB Racing D418 www.kandmacoustics.co.uk |
#15
|
|||
|
|||
This is my Base setup for Dry Astro/Grass and Carpet. I will be giving this to all new Sworkz Team Drivers to use as a good starting point.
Mark Redmond. North/Northwest Team Manager
__________________
CML - AE - Hobbywing - Answer-RC - RossMod |
#16
|
||||
|
||||
This is my setup from today, i would say this is good starting point for a wet setup
__________________
Answer RC team driver Formby models HB Racing D216 HB Racing D418 www.kandmacoustics.co.uk |
|
|