Yokomo YZ-10

[Stuntmonk1]

Hi guys i recently picked up a yz10 and a bosscat. Im in the process of rebuilding the yz10, and the front lower bulkhead has broken, that holds the shock tower on. Looking for a replacement new or used. I got a tub full of spares too, but that's the only bit i don't have. Lol. Also i was told it was a 94, but if you guys could confirm this as im not 100% because i think the top deck is fibrelyte and i have several different types of shock towers. Any help is much appreciated. (Photos should be attached)

Cheers Mitch

[Peakey]

Welcome Mitch I've already seen this and yes it is a 94 with carbon towers and top deck which is either Fiberlitye or CML. Looks like a good base with the all important TCS and what looks like works 93 turnbuckles 😉

My advice would be to strip it and give it a good clean it should clean up well, then see what it needs. I should have a spare bulkhead I'll check and see what I have. Looks like you need a rear tower too but like I said see what else it needs if anything.

[Stuntmonk1]

Cheers Peaky, yes i am going to strip it this week and see if it needs anything else, there are a few little things but Stu said he might be able to sort me out with a few bits im missing.

Will keep posting updates,

Cheers Mitch

[daz75]

any ideas on the part number for the bulkhead?

[Stuntmonk1]

No sorry bud, think ive found the right manual online but it doesn't show any parts numbers.

[Peakey]

There's a manual here but as for part numbers there not great

http://www.competitionx.com/pdf/vehi...-10-manual.pdf

[daz75]

I'm not expert you see I have some new in packet bulkhead but I've no idea if they are for your car

[suparajicon]

I can help with yz10 94´ parts number, I have some old japanese Yokomo catalogues, if needed by someone.

[Stuntmonk1]

We are after the lower front bulkhead part number, sounds like daz might have some nip, but we're not sure which part number corresponds to my car.

[suparajicon]

ZD-300 front bulkhead with cap ?

[Stuntmonk1]

I'm not sure if that's the right part bud. I think that piece is the 1st picture, from what i've found from searching the part number in google. I'm after the part in the second picture. However i am not 100%.

Anyone know how you can get the yellow stained effect off the chassis?

[Peakey]

Yeah the ZD-300 is the cap well that's what I was selling it under wether the whole bulkhead comes in the pack in not sure. I'll check if I've got time tomorrow I'm sure I've got a spre but I'll find out

[daz75]

Originally Posted by Peakey

Yeah the ZD-300 is the cap well that's what I was selling it under wether the whole bulkhead comes in the pack in not sure. I'll check if I've got time tomorrow I'm sure I've got a spre but I'll find out

ah that's the one we were talking about via PM a while back

[Stuntmonk1]

Cheers for the help guys!

[timmy]

Originally Posted by Peakey

Yeah the ZD-300 is the cap well that's what I was selling it under wether the whole bulkhead comes in the pack in not sure. I'll check if I've got time tomorrow I'm sure I've got a spre but I'll find out

If Justin can't find you one i'm 99.9% sure i've got a used lower bulkhead here you can have.

[Peakey]

Originally Posted by timmy

If Justin can't find you one i'm 99.9% sure i've got a used lower bulkhead here you can have.

What haven't you got

[Stuntmonk1]

Cheers Timmy. Out of interest are you still running my old bmax 2, anodised red?

[timmy]

Originally Posted by Peakey

What haven't you got

Lots of things, but the list is getting smaller

[timmy]

Originally Posted by Stuntmonk1

Cheers Timmy. Out of interest are you still running my old bmax 2, anodised red?

I'm not personally but there's a young member at our club, who has learning difficulties but a lot of talent with these toy cars, so I gave it him to run in the Welsh league last year, he loved it, had a good year with it and will be running it again this year.

[Stuntmonk1]

Glad to here its still be used!!