|
#301
|
||||
|
||||
Here is the Set up sheet cleaned up and translated
Thanks to Kentech and Petit RC
__________________
TRF 501x / 502xs / 511 / 503/ 201xr/ 201xmw/ 211xm AE C4.5 Centro / AE CT4.5 Centro / T5M SDRC / SMC / Shop UFO |
#302
|
|||
|
|||
Thank you!
__________________
http://kentech.blogs.se |
#303
|
|||
|
|||
Quote:
going by the 511 manual, diff joints 51286 diff plates 51287, or is this too small in diameter for the bigger 39t gear?? 39 ball diff gear -cannot determine |
#304
|
||||
|
||||
Your not going to find these parts in the TRF511 manual.. they are different from the kit parts... If you might have to order some of these parts from Tamiya.. the Diff rings can be found off the TRF417..
__________________
TRF 501x / 502xs / 511 / 503/ 201xr/ 201xmw/ 211xm AE C4.5 Centro / AE CT4.5 Centro / T5M SDRC / SMC / Shop UFO |
#305
|
|||
|
|||
Gents
Will this part fit my front?? I have 12mm hex wheels, so the standart part is not good for these. Only rear wheel will fit. http://www.ebay.co.uk/itm/TAMIYA-535...-/310466666584 Thanks |
#306
|
||||
|
||||
Those will work... but you will be very limited on threads on the front axel and you will have to drill out the center of the hex a little bit to make it fir over the axel
__________________
TRF 501x / 502xs / 511 / 503/ 201xr/ 201xmw/ 211xm AE C4.5 Centro / AE CT4.5 Centro / T5M SDRC / SMC / Shop UFO |
#307
|
|||
|
|||
Hmmmm...
Could I use different parts???So I dont need to do any modifications?? Thanks |
#308
|
||||
|
||||
Are the stock front hexs that bad ?
__________________
TRF416 TA05MS F104 TRF503 TRF201XMW TRF203 |
#309
|
||||
|
||||
The larger parts for the 39t diffs are out of the trf511 chassis upgrade set
|
#310
|
|||
|
|||
Front hex's are 10mm
I bought these and they are 12mm....need to get bigger hex http://www.rcjaz.com/tamiya-53880-ta...25-p-7692.html |
#311
|
||||
|
||||
The stock 10mm front hex's are not bad... but the optional DB01 thicker ones are a bit better if your going to run a 10mm front hex wheel that's not Tamiya
__________________
TRF 501x / 502xs / 511 / 503/ 201xr/ 201xmw/ 211xm AE C4.5 Centro / AE CT4.5 Centro / T5M SDRC / SMC / Shop UFO |
#312
|
|||
|
|||
Quote:
so are you saying, if I found a trf511 ball diff complete, that it will not drop straight in the 503, with or without the 39T gear? Quote:
I probably wouldnt get it just for the diff parts however. |
#313
|
||||
|
||||
No thank you ... You always have the good info on your site
__________________
TRF 501x / 502xs / 511 / 503/ 201xr/ 201xmw/ 211xm AE C4.5 Centro / AE CT4.5 Centro / T5M SDRC / SMC / Shop UFO |
#314
|
|||
|
|||
so the 503 gear diff parts like the pulley and diff case 51463 shares in common with the TA06.
I am curious if the TA06 Ball Diff Set 54305 will fit the 503. |
#315
|
||||
|
||||
Quote:
It sucks looking for them because most of the parts are special order
__________________
TRF 501x / 502xs / 511 / 503/ 201xr/ 201xmw/ 211xm AE C4.5 Centro / AE CT4.5 Centro / T5M SDRC / SMC / Shop UFO |
#316
|
||||
|
||||
Might be worth a try... but the outdrives might be short by about 2mm per side.. when I was looking at some of the replacement gear diff out drives I looked at the TA-06 ones.. while they would work.. they are a little short.. I can posy up a pic if you would like to see the difference between them
__________________
TRF 501x / 502xs / 511 / 503/ 201xr/ 201xmw/ 211xm AE C4.5 Centro / AE CT4.5 Centro / T5M SDRC / SMC / Shop UFO |
#317
|
||||
|
||||
Quote:
I finally got mine today, what ESC and lipos are on the PIC in the manual, it looks 1/8 scale electrics???
__________________
TRF416 TA05MS F104 TRF503 TRF201XMW TRF203 |
#318
|
||||
|
||||
The standard front 10mm hex works great with the Tamiya wheels.. but they tend to be on the thin side for most of the B44 front wheels .. and rub on the webbing ... the DB01 wide tread hubs (54406) work best and work with all 10mm front hex wheels
Now some of the 12mm hexs I have posted up before work with the zx-5 and Losi 22-4 front wheels and they do not rub at all.. Now as for the picture of the speed control on the TRF503 instructions... that thing is a Brick!!!
__________________
TRF 501x / 502xs / 511 / 503/ 201xr/ 201xmw/ 211xm AE C4.5 Centro / AE CT4.5 Centro / T5M SDRC / SMC / Shop UFO |
#319
|
|||
|
|||
Quote:
Or I suppose I can hope 37t trf511 diffs can fit, without any clearance issues with it being a smaller diff, as long as the pulley lines up with the belt, and the outdrive bearings line up to the bulkheads. Quote:
|
#320
|
|||
|
|||
what's the part number for the 417 light weight outdrives?
do you use 'blades' with them onroad outdrives? |
|
|