|
||
|
 |
|
||||||||||||||||||
|
#41
18-06-2011
|
||||
|
||||
I raised the inner links as suggested, and that also helped. Now I really like the feel of the car, and cant wait to try at some races.
One more thing, not really related to the setup, but more a general tip; Three of the screws that hold the rear shock tower came loose, and fell out. Well, I guess they came out one by one, but when the third one came out, the rear end started behaving quite strangely, as the entire shock tower pivoted around the last remaining bolt. So threadlock is definately a good idea... 
|
|
#42
22-06-2011
|
||||
|
||||
|
ok quick question for a friend,
ive been asked to convert a b4 into a vega for a friend, he has ordered vega kit and already has a b4 not 4.1 what else will he need ive read he needs the diff but what else bearing for diff drive shafts etc
__________________
Mattys the driver,my names carl
|
|
#43
22-06-2011
|
||||
|
||||
|
The conversion comes with bearings in the box so just B4.1 diff outdrives and your there, the rest will all bolt on just fine!
|
|
#45
22-06-2011
|
||||
|
||||
|
Ah ha, add bearings to your list, my B4 kit had bearings in it, but the 4.1 Vega kit must come with out them.
You get an extra idler gear too, so 4.1 outdrives and bearings and your good to go. Dont forget to dremel the rear arms to give diff out drive clearence and also a 45 deg on the rear hinge pin holder to give the motor clearence. Only a 5 mins job. There are pics on Vega thread of where to take the material from
|
|
#46
24-06-2011
|
||||
|
||||
|
what wing mounts does he need>?and defo no bearings in the kit?
__________________
Mattys the driver,my names carl
|
|
#48
24-06-2011
|
||||
|
||||
|
to be honest theres very little in the conversion gearbox, chasisis, bttery strap and shock tower,motor mount no wing mounts no bearings
__________________
Mattys the driver,my names carl
|
|
#49
24-06-2011
|
||||
|
||||
|
As far as i am aware you will get the following:
Chassis Motor mount Gearbox Rear shock tower Extra idler Body shell And i am pretty sure the X11 wing mounts. None of the conversions come with bearings. If the wing mounts are not there then just give Team Xtreme a call and they will be more than willing to send them.
__________________
X Factory UK - Team Corally - DMS Racing - Tuning Haus - Exotek - Avid - Alpha - JConcepts
|
|
#50
24-06-2011
|
||||
|
||||
|
?
As I said my 4.1 conversion DID come with wing mounts!
As for the bearings I didn't need any extra as I converted a 4.1 ! I think you can buy a non 4.1 conversion that gets round having to buy new outdrives/ bearings not 100% sure on that ! Maybe you friend should have bought that one !
|
|
#51
24-06-2011
|
||||
|
||||
|
Quote:
__________________
Mattys the driver,my names carl
|
|
#52
24-06-2011
|
||||
|
||||
|
sorted
__________________
Mattys the driver,my names carl
|
|
#53
29-06-2011
|
||||
|
||||
|
Any suggestions for clay..?? My b4.1 vega has setup like the general setup + weights as rudebits (servo, speedo, under lipo). Car steers well with holeshots on rear and jc grooves on front, but tends to loose rear grip too easily exiting corners?? Motor nosram 8.5
__________________
AE B44.1 Vega Elite B4.1/TRF201 TLR 22 Tardis MI4CXL
|
|
#54
30-06-2011
|
||||
|
||||
|
Try more rear anti squat, I race my one on low grip and have 4 deg spacers under toe in link.
You could try more rear toe in or lower the rear link on shock tower??
|
|
#55
30-06-2011
|
||||
|
||||
|
Try removing some of the weight from the front and/or add some at the back. It sounds like you may have too much up front. On my rb5 version in low grip I often remove all of the under speedo weight to shift the distribution back.
Lowing the front inner ballsud will let the car come out of the turn straighter and help it get into the turn also. The Inner shock position on the rear wishbone will also give more drive.
|
|
#56
01-07-2011
|
||||
|
||||
|
Thanks guys! Removed under speedo weight. Removed the inner spacers under front camber links. Pos. Outer: inner, inner: inner. Rear: outer: 3rd from out, inner 2nd from in, pos low. Now 20g under servo, 82g under lipo. Front shocks ae piston 1 + sch 35wt, blue spring, top middle, lower outer, height 24mm. Rear ae piston 1 + sch 30wt, silver spring, top outer, lower outer, height 24mm. Camber -1 both ends. Toe: front 0, rear 3 + 0.5 hubs. anti squat 0. Caster front 25. Nosram bl 8,5, nosram istc v2 boost 1, feel 1, no auto brake. Tires: proline holeshot 2 rear, jc barcode front.
Car is quite good now, anymore suggestions???
__________________
AE B44.1 Vega Elite B4.1/TRF201 TLR 22 Tardis MI4CXL
|
|
#57
14-07-2011
|
||||
|
||||
|
Are there any astro set ups for the Vega B4.1 around??
Quick question on weight in the car, I have a Trish bits brass bulkhead fitted and noticed the Kyosho Vega lads don't tend to run these in their cars, would this be the same in the B4.1 car??
|
|
#58
14-07-2011
|
||||
|
||||
|
Quote:
__________________
|
|
#59
14-07-2011
|
||||
|
||||
|
Nice one Tony
__________________
CML Raceway : Imagineering: www.Trishbits.com : MK racing : Buds Balls :Schumacher : DC Painting : Mr O Foams
|
|
#60
14-07-2011
|
||||
|
||||
|
Ah ok, thanks Tony. Slow reaction is good for me! lol
Any other Vega B4 owners running much weight an where??
|
 |
|
|
Xtreme - VEGA
Linear Mode
