|
#1
|
||||
|
||||
Tp-Parts: "Timing" 2 belt driven 1/16 4wd Buggy
Season 11-12 project..all 1/10th parts based little 1/16 Buggy
Custom chassi Custom towers Custom topdeck Custom front belt (order tomorrow) CC CM26-6800 motor (3.17 axle) FIrst spy shot of my chassi Ali-parts Rear Side wiew Test mount Enjoy /T |
#2
|
||||
|
||||
Looks superb Thomas, great work!
Mini 511! If it goes as well as it looks your on to a winner! |
#4
|
|||
|
|||
That looks fantastic. Great work!
__________________
Schumacher KC, KD, CAT XLS, CAT L1 | Team C TM2 V2, TM4, TC02 | JQ The Car | Mugen MBX6 | Losi 8T,8BE 1.5 | Durango DEX-410V4 | FTX Blaze | XRAY M18T | Kyosho STR,Surf Dude,Nexus 30 | Nimrif Makara | MFA Spear | She Devil | T-Rex 450SEV2,250SE | Ark X-400 | Protech Butterfly,Zoom 400 | Ikarus Piccolo | VW T4 | Smart 450 | KC-250 | BoltRC Kraken 5" | Emax Nighthawk 250 | Gravity 250 | S550 | Prusa i3 | TronXY X5A | Must stop collecting stuff! |
#6
|
||||
|
||||
how much??? lol i want!!
|
#8
|
|||
|
|||
Nice!
I once cut and shortend an academy STR-4 tourer into a mini buggy. I ran it with a mini-inferno body on top. Which body are you going for? |
#9
|
||||
|
||||
thats very nice
|
#11
|
|||
|
|||
Moter Mount? You're using a 380 or 360 sized moter, isn't it?
So which moter mount is in the bag, and on the car? |
#12
|
||||
|
||||
Yea, a Novak Three-80 or a Castle CM26
it is the stock mount on the car, the other is almost the same, but with a better spur/pulley holder. about lid, not sure yet. |
#13
|
|||
|
|||
I'm a little confused: I'm not very much at home in Tamiya.
(It is using Tamiya touring car parts for the transmission , right?) So how do you fit the 360 sized moter on a 540 sized moter mount??? |
#14
|
||||
|
||||
Tp-Parts Timing 1/16 4wd belt driven Buggy vs Carisma Tp-Parts Chassi GT14B 1/16 4wd saft driven buggy
(shocks are only mounted for pic, have to order a new set, this is Aduis shocks) Geardiff installed, new motormount with quickchange gear Some drilling and cuting |
#15
|
||||
|
||||
Ordered All Schumi parts,HPI and will get the Kyosho parts Monday i hope...if im lucky the belts will arrive mid this week, ordered some new bigger center pulleys to.
Have done som small mochup mount with the Xray M18T crank, lloks good..see wich one il use, i cross my fingers that the arms will fit in between the mounts.. |
#16
|
||||
|
||||
Schumacher CAT SX arms fitted..Next, to get the HPI rear hub and Lazer front end..then it is measuring again,dremel,sanding the arms, to get the width good, next tricky par is to extend all CVDs...
|
#17
|
||||
|
||||
Looking ace Thomas ,as per normal!
I like the look of your two1/16ths
__________________
|
#18
|
||||
|
||||
Thank you Rebel, do my best =)
Belt arrived today , Jiiiippie Just compared the Stock Tamiya arm, with my cut Schumi... No doubt, that il go for the Tamiya one, so much easier and less sandning,dremling |
#19
|
||||
|
||||
Would be awesome, i think it is to long, but that would be real cool
UPDATE Ok, so there was no time today for any practice, so i took the chance to do some work on the Timing car :rawk: And, i must say, i do believe more and more on this car, just waiting for the new front belt from Schumi UK Using the Kyosho Lazer 4wd plastic inserts for the arm-axles reduced the sloppy a lot.. Left: Tp-Parts Timing 4wd Buggy - Right: Carisma GT14B 4wd Buggy Rear Front |
#20
|
||||
|
||||
Quote:
Btw who are you ordering youre belt from ??? mvh Isobarik |
|
|