|
#1
|
||||
|
||||
Tamiya 511 Upgrade Kit - Fitted pics
Thought a few of you would like to see what`s included, and what it looks like fitted.
|
#2
|
||||
|
||||
Very nice indeed Rich. Can't wait to get mine!
|
#3
|
||||
|
||||
Cheers DC. You must have half a dozen ordered .
Diffs are a lot better. Watch out for the lipo mounts. They look the same but are slightly different. You will need a new hole for the aerial too. Quite a big job to fit ! |
#4
|
||||
|
||||
Very nice Rich
|
#5
|
||||
|
||||
Quote:
Haha, only 3, even though I have many 511's . Cheers for the advice. |
#6
|
||||
|
||||
So what do you get in the box and how much does it cost ?
__________________
Schumacher KF2 SE Schumacher K2 Schumacher Racing, MB Models and Rc Genius |
#7
|
||||
|
||||
Mine arrived last night and it comes with a new slim chassis, new motor mount (more centrally located), new diff halves with keyed diff plates and 39t pulleys also longer drive belts and (presumably) the 502X battery mounting plastic parts.
Think that's it apart from a few odd screws and spacers. Of course i'm assuming that by putting all this on the car I will become a world champion and all for a shade over £100. Bargain!
__________________
rcLazy.com = blog + shop 01202 247434 +facebook + twitter + youtube +balls + bearings + goo + lots lots more... |
#8
|
|||
|
|||
Two threads same topic... in the original thread I observe that they want us to "cut" an aluminium part (step #17, BD20) - how does this work?
|
#9
|
|||
|
|||
Quote:
Looking at the manual posted on the Stella Models website, I'd say its not so much a "cut" that's required, but to file down some of the part (BD20) so it does not rub against the newer, larger 39T pulley. Get out your dremel or file and take a little off at a time, check & re-check your fit and clearances. |
#10
|
|||
|
|||
Quote:
|
#11
|
||||
|
||||
How much is it ?
__________________
Schumacher KF2 SE Schumacher K2 Schumacher Racing, MB Models and Rc Genius |
#12
|
||||
|
||||
I ve been looking at this kit aswell the cheapest ive seen it for including shipping is 109 pound.
Whats putting me off at the min is are the belts available if you was unlucky to do one,are the diff rings available,and also what is the main advantage of the upgrade kit whats it change to the handling of the 511. Thanks. |
#13
|
||||
|
||||
Quote:
Front hinge pin brace needs a fraction from it, its minimal. Manual also states that the steering base needs filing. Mine clears, its close but it doesnt need adjustment. Will recheck once the belts are run in and re tensioned. Quote:
The kit has been developed with team driver feedback to optimise the car for lipo use. Remember the car was designed with NiMh cells in mind. The chassis is narrower and it generally places the weight nearer to the centre. Diff design is improved to prevent dirt ingress aswell as the change in pulley size. Rear (front) suspension pivots are also included. The Diff outdrives include flat surfaces to prevent diff slip that sometimes occurs on high grip surfaces. From an advert ....... - Brand : Tamiya - Part No : 84315 - Item Type : RC TRF511 Chassis Upgrade Set - This parts set is designed for the TRF511 Chassis and includes a wide range of race-spec Option Parts to further improve its performance potential. - The new carbon lower deck and aluminum rear suspension mounts enable the chassis to be compatible with square-shaped battery packs. - The new aluminum motor mount shifts the motor position towards the center of the chassis. - In addition, the use of 39T pulleys results in an optimum secondary gear reduction ratio. Set Contents - 2.25mm Carbon Fiber Lower Deck (new) - Aluminum Rear Suspension Mounts (new) - Aluminum Slide Motor Mount (new) - Aluminum Center Bulkhead Bridge (new) - Diff Joints (Front & Rear) (new) - Drive Belts (Front & Rear) (new) - TRF502X J parts (battery holder) - 39T Ball Diff Pulley (Front and Rear) - TRF417 Diff Plates (Front and Rear) - Compatible with TRF 511 chassis ONLY |
#14
|
||||
|
||||
I,ve looked at the instructions on the Stella site and the parts are listed in Japanese, is there any english available?
|
#15
|
||||
|
||||
Replacement part numbers are listed in the upgrade manual. Most of them likely to be special order i would imagine. That doesnt mean that they arent available though. Just takes a little longer to get them.
|
#16
|
||||
|
||||
Quote:
I've never stripped a belt on my 511 and I got it on pre-order back when it was released. As for the rest I think Rich sums it up well... Quote:
Quote:
Quote:
|
#17
|
||||
|
||||
Thanks Rich for info.
|
#18
|
||||
|
||||
Thanks for the parts list
|
#19
|
|||
|
|||
...too bad none of those part numbers are recognized on Tamiya's website, Google doesn't even know what they are!
|
#20
|
||||
|
||||
Quote:
Never had any problem getting parts for the 511 myself. Some you just need to order that's all. |
|
|