|
#101
|
|||
|
|||
Thanks for the info...
|
#102
|
|||
|
|||
New body ready for racing!
|
#103
|
|||
|
|||
Very smart, nice job
__________________
Martyn Kyosho | Team Orion | Sanwa | Rudebits | Proline |
#104
|
||||
|
||||
new body for me too...
Rattle cans FTW
__________________
yes..... it's a dead sheep... |
#105
|
|||
|
|||
Awesome
__________________
Martyn Kyosho | Team Orion | Sanwa | Rudebits | Proline |
#106
|
||||
|
||||
supastox
best thing since sliced bread when it comes to 1/12 saloon , handles great , love racing both my supastox
__________________
why have one when you can have two |
#107
|
||||
|
||||
Anyone else's chassis not flat when it's all assembled?
Put a steel straight edge on mine and I can rock it front to rear by 1, 2mm. Did look at a few others and mine was not the worst but all chassis's were warpped. So after stripping the car here's a short video of a warpped chassis. As you can see a not so flat SS chassis. Your supposed to race with this car. . Not impressed. This is from the 4c/1s kit and has done about 6 runs in practice not racing using 1s/13.5 to power it. Ruler is aprrox 1 to 1.5mm.
__________________
o0ple Trader Feedback NE Venue's New & Old my space on YouTube CFR RCTV Channel Glenn Atterton BRCA 2005 1/10th Off-Road Veterans Champion LMP12 National Champion 2003/2004 / F3 class |
#108
|
||||
|
||||
Put the chassis in the oven at 200c in the vain hope I may be able to flatten it. Not a chance. Nice and flexible when it came out. Put it between to plates of glass with heavy weight on it. Still has the same tweak in it. Bugger. No video this time as it'll only be a repeat
__________________
o0ple Trader Feedback NE Venue's New & Old my space on YouTube CFR RCTV Channel Glenn Atterton BRCA 2005 1/10th Off-Road Veterans Champion LMP12 National Champion 2003/2004 / F3 class |
#109
|
||||
|
||||
both of mine are fine!!
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD |
#110
|
|||
|
|||
Hi,
Did you try contacting Schumacher regarding the warped Chassis to see if they know of the problem? Whenever I have had problems with parts in the past (Not very often I must add) they have been great, and often sent out replacement parts. I certainly found I got much more information and help as a result of speaking to them direct than I suspect I would have posting about it on a forum!! May be worth thinking about. Last edited by lee150978; 16-07-2012 at 08:46 PM. Reason: mistake |
#111
|
||||
|
||||
Quote:
Bought unused from o0ple'r who had built it but it was unused.
__________________
o0ple Trader Feedback NE Venue's New & Old my space on YouTube CFR RCTV Channel Glenn Atterton BRCA 2005 1/10th Off-Road Veterans Champion LMP12 National Champion 2003/2004 / F3 class |
#112
|
||||
|
||||
My chassis was fine and ive had a look at quite a few others that were built and unbuilt which were ok as well.
If you didn't build it, it's possible it got tweaked when it was built I'd contact Schumacher and see what they say, I'm sure they will help if they can
__________________
WWW.SERVOSHOP.CO.UK |
#113
|
||||
|
||||
can you run one saddle pack instead of a shorty lipo?
|
#114
|
||||
|
||||
Have found that it you do not tighten the battery tray evenly or overtighten it the chassis can get a tweak which warps the chassis, so my eyes dodgy building
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD |
#115
|
||||
|
||||
do you mean a saddle pack or one half of one?
if one half then yes but you'll need to find a way to stop it moving side to side when cornering
__________________
o0ple Trader Feedback NE Venue's New & Old my space on YouTube CFR RCTV Channel Glenn Atterton BRCA 2005 1/10th Off-Road Veterans Champion LMP12 National Champion 2003/2004 / F3 class |
#116
|
||||
|
||||
I'll mount the tray on the underside and see if it pulls it straight then before I rebuild the car.
__________________
o0ple Trader Feedback NE Venue's New & Old my space on YouTube CFR RCTV Channel Glenn Atterton BRCA 2005 1/10th Off-Road Veterans Champion LMP12 National Champion 2003/2004 / F3 class |
#117
|
||||
|
||||
Quote:
thanks,ill have to do some fettling |
#118
|
|||
|
|||
Could anyone tell me if the body shell for the Schmacher Supastox would be able to fit onto a Tamiya RM-01 chassis?
Thanks in advance. |
#119
|
|||
|
|||
Given this has been resurrected - I have just painted my first shell. Leaked a little under the tape - and is it's a basher shell - I just used whatever I had to hand (in this case, automotive paint)
Oh and when I put the car down to get my phone, I then found the dog next to it! |
|
|