|
#1
|
||||
|
||||
XRAY XB4 Setups
Come on chaps
how did worksop go |
#2
|
||||
|
||||
Ill start. It took most of the day to get the car how I wanted it but in the end it was 99.9%. I drove like a tit which hampered the process but I was very happy with the car. It was bullet proof too coming home completely unscathed despite my best attempts to wreck it on more than one occasion. Ill attempt to post a setup or link to it over the coming days. Overall a great day.
__________________
PBM Racing 01773 769323 TEAM XRAY RC DISCO |
#3
|
||||
|
||||
Nice one Si,
did you start with kit setup? |
#4
|
|||
|
|||
I ran my xb4 yesterday, first couple of rounds car was very good, but after that i seemed to be loosing rear traction espeically in the fast sweeper at the end of the straight, car seemed to want to kick out.
Used pretty much kit setup - played with multiflex system, tried progressive springs, and different roll bars. We probably try using 6 hole pistons at next round, unless i find something else |
#5
|
|||
|
|||
Mixed day for me went wrong with setup untill 3rd round then car was dialed! Tried most of the things as mark did. ended up with good top 20 pace but still a bit of work to do to increase rear traction as the car rotates mid corner on the slippery surface.
I'll post my settings online tonight so you can see where i ended up with it. Very promising for the cars first run in these conditions Colin
__________________
PBM RACING - RC DISCO - SMD - XRAY - SANWA - LRP - PAINT BY COX'Y |
#6
|
|||
|
|||
i ran the xb4 at silverstone on saturday finnished 3rd setup below
http://forum.teamxray.com/xform/inde...D=15&setup=xb4 |
#7
|
||||
|
||||
My finishing setup from Worksop is here. You'll prob have to copy the addy into your browser as I'm not smart enough to make it into a link. Sorry. Lol
http://forum.teamxray.com/xform/inde...D=20&setup=xb4
__________________
PBM Racing 01773 769323 TEAM XRAY RC DISCO |
#8
|
||||
|
||||
It works. Lol. Who'd have known. Anyway, the car was really nicely balanced like this and great to drive. Good alround traction and no over rotation. Loved it. Deffo my start point for the next meeting. Great car!!!
__________________
PBM Racing 01773 769323 TEAM XRAY RC DISCO |
#9
|
|||
|
|||
do some one have a set up for bumpy dirt??
In winter we drive in a manege in the netherlands, next race I would like to drive my xb4, that's the reason I am looking for a basic dirt set up http://www.youtube.com/watch?v=FPEYV5l3AB8 http://www.youtube.com/watch?v=tekpPlYK6OY temp between 0° and 8° lose dirt whit big holes in it popular tyres : losi step pin thanks!! grtzz
__________________
www.m-r-v.be |
#10
|
||||
|
||||
will have a setup in no time there .
and tyers I will run my proline calibers . dont want to get a truck load of tyers just for 1 race and the calibers we can use at the nationals . will probebly go 4 hole pistons . all the rest will take 30 min to get it good . ow and softer diffs so get some emty one's ready to fill .
__________________
topspeed modelshop Ralls racing Rc-speedhouse Rude-Bits Serpent Fba section offroad chairman. |
#11
|
||||
|
||||
Quote:
Nice one Si,ill be starting with that to just need a spring set |
#12
|
||||
|
||||
Just back in from Mansfield club night. Car was setup on my Worksop setup and it was properly dialled. Absolutely mega. Loving this car. For those not familiar it's an indoor carpet track with good jumps and rumble strips. Great midweek venue with increasing numbers.
__________________
PBM Racing 01773 769323 TEAM XRAY RC DISCO |
#13
|
|||
|
|||
Quote:
4 holes, how many mm for one hole? (front /rear) 4 holes front and rear? grtzz
__________________
www.m-r-v.be |
#14
|
||||
|
||||
will say this in englich so all understand as aee is belgium aswell lol. cal me as putting a full setup on here we cant at the moment. we are driving in a horsstable and last week we had 12 degrees and this week its -4 so oils and all ????? lets see that in 2 weeks . al the rest call me up will be a lot faster . greets
__________________
topspeed modelshop Ralls racing Rc-speedhouse Rude-Bits Serpent Fba section offroad chairman. |
#15
|
|||
|
|||
Quote:
thanks for the setup help bart! it was a fun race grtzz
__________________
www.m-r-v.be |
#16
|
||||
|
||||
Hi,I will be running a 7.5 x20 in the car,it says on the instructions for the motor "gear ratio of 10.0.1"
could some one help with the right pinion to start on, also in simple terms how to work it out, thanks |
#17
|
||||
|
||||
Quote:
To work out the ratio, I think it goes, number of teeth on spur divided by pinion size, times internal ratio of 2.5. example 81t spur divided by 20t pinion, times 2.5 ratio gives you 10.12.
__________________
Model Junction, Boughton Raceway. |
#18
|
||||
|
||||
Thankyou John,perfect
Does anyone use a free iphone app?iv done a search but they are all abit pants |
#19
|
||||
|
||||
I run my 5.5 and 6.6 on a 18 and 19 pinion . indoors I run it on a 16 .
you may not forget that most of ower tracks are a lot smaller than the UK tracks , and I am running HPI motors and they are not getting above 60 degrees at enny time not even with a full pack of driving .
__________________
topspeed modelshop Ralls racing Rc-speedhouse Rude-Bits Serpent Fba section offroad chairman. |
#20
|
||||
|
||||
Robin hood setup
Has anyone had the xray round robin hood yet on the astro?
I'm looking for a setup. Thanks.
__________________
FEEDBACK: http://www.oople.com/forums/showthre...257#post750257 |
|
|