|
#41
|
||||
|
||||
Quote:
Quote:
Lee i dont need ribs i bring enough pleasure to ladies lives as it is. A
__________________
Ashley Williams I always thought by 2013 we would have flying cars, but we have got blankets with sleeves! |
#42
|
||||
|
||||
Quote:
but darren they would not be able to run new nimh either
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD |
#43
|
||||
|
||||
your such a liar
|
#44
|
||||
|
||||
Quote:
Lee i never lie. A
__________________
Ashley Williams I always thought by 2013 we would have flying cars, but we have got blankets with sleeves! |
#45
|
||||
|
||||
ok ash but hoovering the living room for your mum doesn't count as providing a pleasurable experience for a woman
|
#46
|
||||
|
||||
*Her* pleasure, even.
__________________
|
#47
|
||||
|
||||
|
#48
|
||||
|
||||
Then again, you can't wear an X-6 chassis inside-out...
__________________
|
#49
|
||||
|
||||
I haven't tried
|
#50
|
|||
|
|||
Doubt it makes a diff when all you can have is royal ones....
|
#51
|
||||
|
||||
He likes them because it tickles his palm
|
#52
|
||||
|
||||
Battery bay ribs are intact like said before for strengthening reasons. I only removed the one in the 2cell bay to give a flat floor to the esc.
But personally I would like to see a factory chassis without cell holes (or even filled thin enough to cut with an x-acto if you wish to use nimh). This way we give preference to lipos, the future right now. Lowering the lipo is other story.. Is the X60 chassis made without cell holes? |
#53
|
||||
|
||||
Just had a look at Big E's car, what servo horn is that? the steering link looks a better angle, is it a losi one? if so any know a part number .... Darren??!! lol
|
#54
|
|||
|
|||
Its the Losi one from the XXX part no A1620......
__________________
ORCA - LC RACING - RUDDOG PRODUCTS - JCONCEPTS - ALPHA PLUS - TEKIN RACING - ULTRAPOWER AVID R/C - VAMPIRE RACING - EXOTEK RACING - LUNSFORD RACING - X-FACTORY - TUNING HAUS - WTF AME - RAGE R/C - REVOLUTION DESIGN RACING PRODUCTS - McKUNE DESIGN - TEAM AZARASHI X-PARTZ - PHAT BODIES - RACERS EDGE - RM2 - DIRT RACING PRODUCTS - DMS INSERTZ TKR GRAPHICS - BF MATERIALS - BATAN - DMS PARTZ - TEAM AJ Tel : (01923) 816636
|
#55
|
||||
|
||||
Any idea about the carbon lipo retention?
Thanks |
#56
|
||||
|
||||
Poor Spencer - his thread got well and truly raped!
G
__________________
Graham North http://www.atomic-carbon.co.uk https://www.facebook.com/atomiccarbon https://www.facebook.com/nortechracing |
#57
|
||||
|
||||
I feel dirty G.
|
#58
|
||||
|
||||
__________________
Mattys the driver,my names carl
|
#59
|
|||
|
|||
Lmao, i didn't even read the first post, i just thought it was about chassis cutting and shizzle.
|
#60
|
||||
|
||||
Since this thread got off track in this direction (mostly talking about the second-half of the link below), and 3 days isn't quite too dead to res back up, I thought I'd post this little announcement here: http://www.2wdrc.com/News/12-08-2008.htm
|
|
|