|
#1
|
|||
|
|||
Novak GTB fan
Anyone know where i can get the novak black fan, but not a novak one if you know what i mean. Needs a receiver plug and to be the same size.
cheers |
#2
|
|||
|
|||
get a much more fan. screws straight on, can't remember if its 25mm or 30mm
__________________
www.theraceplace.co.uk |
#3
|
|||
|
|||
Does it clear a b4 body? Do you do them John? £?
|
#4
|
|||
|
|||
its fitted in joe's yok, they are about 7quid ithink but no i havn't got one
__________________
www.theraceplace.co.uk |
#5
|
|||
|
|||
Cool, thanks john. so what do ppl suggest the 25 or 30 mm one? Ive found a shop that sells both....
|
#6
|
|||
|
|||
give me 5 mins i will go and measure the one on joe's yok
__________________
www.theraceplace.co.uk |
#7
|
||||
|
||||
You will need the 25mm one, the 30mm is too big!
M. |
#8
|
|||
|
|||
Cheers john, also what guage wire do you use, 14 or 16?
|
#9
|
|||
|
|||
30mm and usually 14gauge
__________________
www.theraceplace.co.uk Last edited by modelimages; 19-11-2007 at 01:09 PM. Reason: added extra |
#10
|
|||
|
|||
Thanks guys
|
#11
|
||||
|
||||
Stock fan is 30mm wide, optional smaller one is 25mm, think the 25mm one is thicker though.
__________________
Nortech is ACE! |
#12
|
|||
|
|||
Right at the moment i have the std black novak fan, from what i can you you just put the screws through the fan and slide it into the heatsink fins? Will 2 screws just slid in hold it? Can i just put the fan straight on or do i need to put some plastic washers inbetween? I feel like such a noob
|
#13
|
|||
|
|||
30mm much more fan i use.
i took out the washers and screwed it straight to the heatsink as it was a squeeze in the ZX5. I also wired it to the 7.2v of the speedo for extra air shifting in the 4wd. In the B4 it should be fine off the standard BEC. some people run the 25mm fan in 2wd and mill out the heatsink slighty so the fan sits semi-inside the heatsink so it fits under low shells.
__________________
4wd - X4TE 2wd - X2C (Mad Rat passed down to son!) Ansmann Racing UK RIP - MicroTech Racing Trader Feedback |
#14
|
||||
|
||||
try this place. http://www.brockmodels.com/index.php...a9472999e46c73
|
#15
|
|||
|
|||
I have a much more fan on order anyway, my main question is do you just slide it in or screw it in? From what i can see it holds well but can only reach on one side, which is just two screws....
Cheers guys. |
#16
|
|||
|
|||
Muchmore 30mm fan, you screw it on, you dont need the washers if you want it more low profile, 2 screws is plenty strong.
__________________
To Finish First, First you must drive fast |
#17
|
|||
|
|||
But theres no threads, their just slots in the heatsink lol.
|
#18
|
||||
|
||||
On my GTB the stock fan was held on with plastic screws
__________________
Canon 40D (350D backup) - EF-S 18-55 - EF-S 17-85 - EF 100-300 - EF 50 - Canon 430 EX || Speedlite - Canon BG-E2N Grip Adobe Photoshop CS4 Extended AX-10 Crawler - Thats all I have left!!!
|
#19
|
|||
|
|||
my 30mm MMR fan came with screws and spacers. its right, there is no thread in the heatsink, just grooves.. the screws just push into them.. its a bit naff in my opinion. My original fan broke so i bought fiver MMR ones from Hong Kong. i even bought the little finger guards so i dont cut my fingers off...
Neil |
#20
|
|||
|
|||
Cheers guys.
|
|
|