|
#381
|
||||
|
||||
i was told next week for both kits
and i will not say who |
#382
|
||||
|
||||
yes next week. i got an email from mb stating my 210 will be with me next week. i think the next batch of v3,s will be here at the same time.
|
#383
|
||||
|
||||
HI
On the durango build guide to diffs it says that it may be worth while to use the orings from a 408 is this still the thing to do with the v3 or has durango updated the seals for them? Thanks |
#384
|
|||
|
|||
Seals the same as the ones from the 408 come supplied in the v3 kits now mate
__________________
~ICON-RC~ATOMIC CARBON~LMR~TONISPORT~NUCLEAR RC~
|
#385
|
||||
|
||||
Ideal just dont want to start building to find out they was not
thanks |
#386
|
|||
|
|||
They were in my kit anyhow. Might be worth firing Skelding a pm to check
__________________
~ICON-RC~ATOMIC CARBON~LMR~TONISPORT~NUCLEAR RC~
|
#387
|
||||
|
||||
The 408's seals are listed as std parts on the V3's parts list.
__________________
Model Junction, Boughton Raceway. |
#388
|
||||
|
||||
I have some kyosho and tresrey o rings from my previous ownership
|
#389
|
||||
|
||||
They are in the kit , I took a pic and posted it a few pages back, as mentioned they are listed ,but as shock seals in the instructions
Fyi,Post #274 3rd pic down shows the seal |
#390
|
||||
|
||||
The machined diff gear isn´t included int he V3, isn´t it? You have to buy it seperately?
|
#391
|
||||
|
||||
Correct Correct my friend .
__________________
Bmcc . |
#392
|
||||
|
||||
Am i right in saying the diff gear in the v3 is different im sure it has no locating lugs?
|
#393
|
||||
|
||||
I think that's been the case for a while now, it's not just a V3 thing.
__________________
Model Junction, Boughton Raceway. |
#394
|
||||
|
||||
Hi everybody,
Yesterday start to build my new V3))) After build and painting show photos))) It's will be in my new design))) Have a nice day all)
__________________
As body paint as he goes..™ |
#395
|
||||
|
||||
i need to reposition the servo wire and adjust the spacing between the fr shocks and drive shaft am i using the wrong standoffs?
__________________
2WD Kyosho RB6 |
#396
|
||||
|
||||
..I have some situation but I think it's all is correct...
__________________
As body paint as he goes..™ |
#397
|
||||
|
||||
does the new V3 have new rear hubs that use bigger bearings or are they the same as the previous models?
many thanks lewis
__________________
Durango DEX410R
Durango DESC410R losi 8ight 1.5 team got nitro driver www.gotnitroonline.com <----- check it out! |
#398
|
||||
|
||||
The 1 degree hubs have the larger bearing but the 0 ones are the same small bearing as before. Or they were in my kit anyway.
__________________
Lets Off Road! |
#399
|
||||
|
||||
yes, i did not have the bearings for the 0deg hubs in the kit however
__________________
2WD Kyosho RB6 |
#400
|
||||
|
||||
Same for me and yes the Front Spring Retianers touch the Universals slightly when on the inner hole on the wishbone. Moved it to the outer hole. Should be fine, if i need the inner hole i will use a small spacer.
|
|
|