|
||
|
 |
|
||||||||||||||||||
|
#1
15-10-2014
|
||||
|
||||
Team orion 10.1 problems
Just getting everything wired up and I've got the Esc in and soldered up so just got round to programming the Esc for the first time.
I've turned it on to bind up the reciver and the red light is continuously flashing and beeping. I've charged up the batteries so it can't be that but it just won't do anything other than beep? What the f*** have I done wrong ?
__________________
My feedback feel free to add anything  http://www.oople.com/forums/showthre...863#post861863 
|
|
#2
16-10-2014
|
||||
|
||||
|
They flash and beep in set up mode for the throttle stick end points when the setup button is pressed simultaneously with the on button. Is the setup button sticking? Are you pressing the setup button when you switch it on?
__________________
 PBM Racing 01773 769323 TEAM XRAY RC DISCO
|
|
#3
16-10-2014
|
||||
|
||||
|
The setup button dose t seem to be sticking you can feel and hear it clicking. It dose the same if you just turn it on and then turn it in holding the setup button.
The rx is bound as I've got steering It won't go into calibration mode. It beeps with a 1 second gap and the red light flashes.
__________________
My feedback feel free to add anything http://www.oople.com/forums/showthre...863#post861863
|
|
#4
16-10-2014
|
||||
|
||||
|
What kind of radio gear are you using? I had a friend who had issues with an Orion speedo when he was using original DSM 1 receivers.
__________________
Team Associated Hobbywing SRT Reedy My feedback http://www.oople.com/forums/showthread.php?t=63097
|
|
#5
16-10-2014
|
||||
|
||||
|
Ko propo Helios Spektrum converted with a micro rx. But even with that unplugged it still won't go into calibration mode all it will do is flash and beep.
__________________
My feedback feel free to add anything http://www.oople.com/forums/showthre...863#post861863
|
|
#6
16-10-2014
|
|||
|
|||
|
Try a different motor, apparently some arnt compatible with orion speedos or maybe a sensor/ sensor wire fault
|
|
#7
16-10-2014
|
||||
|
||||
|
It should still set up tho. It's usually just the set up box that doesn't work with another type of motor.
__________________
Team Associated Hobbywing SRT Reedy My feedback http://www.oople.com/forums/showthread.php?t=63097
|
|
#8
16-10-2014
|
||||
|
||||
|
It's an orion motor and I've got the new setup box and that won't connect to re Esc
__________________
My feedback feel free to add anything http://www.oople.com/forums/showthre...863#post861863
|
|
#9
16-10-2014
|
||||
|
||||
|
It might be in set up mode!
First thing to do is turn esc on then press and hold set up button for a second or 2 until green led flashes. This re-sets the esc. Then try again. Also what Lipo are you using? is it 7.4 volt?
|
|
#10
16-10-2014
|
||||
|
||||
|
Orion carbon pro saddles, I don't think it's in setup mode all it will do is beep every second with the red led flashing
__________________
My feedback feel free to add anything http://www.oople.com/forums/showthre...863#post861863
|
|
#11
20-10-2014
|
|||
|
|||
|
Have you reversed the throttle on the transmitter?
|
|
#12
21-10-2014
|
||||
|
||||
|
No it's sorted now it had a fit started flashing all colours, loads of beeping then stopped and has been fine ever since.
__________________
My feedback feel free to add anything http://www.oople.com/forums/showthre...863#post861863
|
 |
|
|
Linear Mode
