|
#101
|
||||
|
||||
Heres my setup for eastrax from today.
__________________
http://www.rprcdistribution.com |
#102
|
||||
|
||||
Here!
__________________
http://www.rprcdistribution.com |
#103
|
||||
|
||||
I'm trying to keep the rear end from swinging out under acceleration, do I tighten or loosen the diff?
__________________
SHUMACHER CAT SX SHUMACHER COUGAR SV |
#104
|
||||
|
||||
Hy Guys,
for those who run non loose dirt ... give the saddle configuration a try ... It's really cool regards Tom |
#105
|
|||
|
|||
Well another night down and further testing on hard pack high bite clay.
Front: stock upper mount stock lower mount 4 hole 32.5 3.5 spring stock ball stud height outer camber link on castor block stock ackerman 5* castor block Associated inline steering block w associated stub axle reversed front arm 0 Toe -1* camber Rear: 72t spur/26 2.6 gear stock upper and lower shock mount no sway 4 hole 32.5 Losi rear arm shaved and shimmed 1mm foward Camber plate lowered plastic spacer on top inner ball stud lowered 2mm center hole on hub -1* hubs full foward Diff low stock anti squat 4* toe -1* camber Modified camber plate 38mm between ball studs Shocks foward 30g weight added to chassis rearmost outer Soft upper deck JC Rulux wheels JC Rounders Proline Holeshot 2.0 SP GT 2.1 w 422 software SP V3 10.5 stock timing The car was the best it ever has been so far. There are still a few thing to try to make it faster. Tonight the car was a 1-2 finish, two Cougars finishing less than a second apart. Amazing wheel to wheel race.
__________________
Star RC Imports on Facebook. Stop in and say hello! |
#106
|
||||
|
||||
Speed Passion gearing?
Can anyone tell me a good starting point for gearing a Speed Passion V3 8.5? & also the settings for the Speed Passion GT2 esc, also if it needs any accessories etc, thanks!
__________________
Serpent Racing / Novarossi / Ko Propo / Proline Racing / KBRL / SRS / Warehouse 3 / One Hobbies / Red Rock Hobbies / Glitch Rc Raceway / Cornish Pasty Co. |
#107
|
||||
|
||||
Hy,
gearing with the standart Spur will be the 23pinion but it also depend on the size of your track ! for the Sp speedo I ran it : 1 3 4 3 4 1 1 1 8 2 and it works great regards Tom |
#108
|
||||
|
||||
Bit out of the FDR for the SP V3 motor I think? May have to re-look at my gearing again. I'm on a 78 /28 - FDR 7.2
|
#109
|
||||
|
||||
Hy,
i ran the 7,5 with the stockspurgear with an 21 pinion on a small track .. regards Tom |
#110
|
||||
|
||||
Quote:
__________________
Serpent Racing / Novarossi / Ko Propo / Proline Racing / KBRL / SRS / Warehouse 3 / One Hobbies / Red Rock Hobbies / Glitch Rc Raceway / Cornish Pasty Co. |
#111
|
|||
|
|||
Heres my oudoor setup. Let me know what you guys think or if there are any questions.
Forgot to add the longer screw and locknut as insurance for the steering bushing. Note: -3 turns on front shock not rear. |
#112
|
|||
|
|||
This is a high bite clay setup. Let me know what you think.
I forgot to add long rear ball cups.
__________________
Star RC Imports on Facebook. Stop in and say hello! |
#113
|
|||
|
|||
Does anyone have any indoor setups? Running full carpet with jumps.
Thanks
__________________
Kyosho RB6 |
#114
|
|||
|
|||
I think i posted a setup for West Bridgford earlier in th thread, take a look at that.
Si
__________________
Schumacher, Hobby Wing, Thunder Power, Anderson, Sanwa, Trishbits, P-Dub Racing, Rudebits, Inside Line, Nuclear RC, RC Domination, RPC |
#115
|
||||
|
||||
Any EPR set-ups from the guys? Trish, Schumacher and Ghea pistons?
|
#116
|
||||
|
||||
anyone got a base for a grass setup or would it be similar to a high grip astro?
|
#117
|
||||
|
||||
I ran mine box standard with slim stagger ribs, 7.5 and trishbits brass was great as it was.
__________________
RETIRED CONSIDERING A COMEBACK |
#118
|
|||
|
|||
Guys, I just wondering why you are reversing the arms? What benefit is it having?
Thanks |
#119
|
||||
|
||||
Quote:
Reversing the rear ones allow to mount the shocks on the rear on the wishbones On the front, that gives you a wheelbase increase of 1.5mm HTH |
#120
|
|||
|
|||
Arno we dont flip the rear arms just move the ball stud for the lower to the backside of the arm.
__________________
Star RC Imports on Facebook. Stop in and say hello! |
|
|