Go Back   oOple.com Forums > Car Talk > Mardave

Reply
 
Thread Tools Display Modes
  #1  
Old 12-10-2013
LongRat's Avatar
LongRat LongRat is offline
Member
 
Join Date: Aug 2011
Location: Bristol, UK
Posts: 240
Default Full Option IMA Integrated Motor Axle

Here are a couple of pics of the new back end I have done for the Mardave, which I am calling the IMA.



The concept is self-explanatory, and the results are very pleasing. The car drives as smooth as silk, and there is no mechanical noise from the lack of gears. The current set up is using a slightly low kv motor (750) which isn't drawing quite enough current as I can complete a race on about 800mAh on a 2-cell. As a result it lacks a bit of punch out of corners but is very comparable with 'normal' cars in straight line speed.
The other benefit is that the whole pod weighs just under half that of a standard plastic pod with 540 size motor and axle.
I am going to switch out the motor for a slightly bigger one (35mm can) to try to get a little more low end. Once that is proven, I will move on to stage 2 of the concept, which will be a customised rotor unit for the new motor with an integral diff.
Judging by the performance of this, it wouldn't surprise me to see all pan cars change to this type of drive before too long. Touring would benefit even more, with biased F/R drives for better cornering, but that would take some customised electronics in the ECSs to achieve.
__________________
Reply With Quote
  #2  
Old 26-10-2013
LongRat's Avatar
LongRat LongRat is offline
Member
 
Join Date: Aug 2011
Location: Bristol, UK
Posts: 240
Default

IMA v2.0
Now using Aerodrive 3536 motor, 910kV.
This is a lot torquier, more powerful, and the fastest solid axle Mardave I've seen. Got second in the A final at this week's club meeting. Now got to make an integrated diff and it will be the complete package.

__________________
Reply With Quote
  #3  
Old 31-10-2013
JimboJames1972 JimboJames1972 is offline
Member
 
Join Date: Jun 2011
Location: Bury St Edmunds, Suffolk
Posts: 69
Default

Really interesting idea here, always good to see others tinkering and thinking outside the box!

Good luck with it,

James
__________________
James Garrett - BRCA GT12 Rep
Reply With Quote
  #4  
Old 31-10-2013
LongRat's Avatar
LongRat LongRat is offline
Member
 
Join Date: Aug 2011
Location: Bristol, UK
Posts: 240
Default

Thanks James, I really think this will be commonplace before too long. It's great to drive.
__________________
Reply With Quote
  #5  
Old 01-11-2013
RogerM's Avatar
RogerM RogerM is offline
*SuPeRsTaR mEmBeR*
 
Join Date: Oct 2007
Location: The middle of off-road nowhere ----- Cheltenham
Posts: 4,258
Default

Do the race regulations allow this though Dave?

Part of the reason I stopped running 'Dave's at the club was that with a car "built to regs" I was totally out paced by the cars built to the club rules then, including your previous car.
Reply With Quote
  #6  
Old 01-11-2013
LongRat's Avatar
LongRat LongRat is offline
Member
 
Join Date: Aug 2011
Location: Bristol, UK
Posts: 240
Default

Apart from 'anything goes' rules I doubt this car would satisfy the regs at any club. Certainly wouldn't at ours. My intention here was to see if the concept worked, which it does, so now I want to perfect it. I've missed enough weeks of our championship to not worry too much about not counting for points.
The rules at Gloucester are still 2S/21.5 or 1S/13.5 to count for points. People who want an easy life, and a cheaper car, go for 2S. People racing elsewhere too go for 1S. The racing is still great and I have to say, the most enjoyable I have had since starting at the club.
__________________
Reply With Quote
  #7  
Old 06-11-2013
grayslick's Avatar
grayslick grayslick is offline
Member
 
Join Date: Sep 2010
Posts: 85
Default

I just wanted to add I have been running with this concept car in recent weeks with a 2s supastox and it runs very smoothly and the current configuration is 100% competitive against the top GT12 runners at the club (GERCC - Gloucester).

It is slightly surreal to see it silently gliding around the track!

Good stuff Dave.
Reply With Quote
  #8  
Old 06-11-2013
mark christopher's Avatar
mark christopher mark christopher is offline
Spends too long on oOple ...
 
Join Date: Jan 2007
Location: haxey, doncaster
Posts: 7,787
Send a message via MSN to mark christopher
Default

Quote:
Originally Posted by LongRat View Post
I really think this will be commonplace before too long. It's great to drive.

that I doubt!
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD
Reply With Quote
  #9  
Old 06-11-2013
LongRat's Avatar
LongRat LongRat is offline
Member
 
Join Date: Aug 2011
Location: Bristol, UK
Posts: 240
Default

Quote:
Originally Posted by mark christopher View Post
that I doubt!
I've heard that before - when I turned up at a track in Summer 2000 with 3 wires coming out of my motor.

With this layout the one thing that can't be escaped is the high efficiency. It is currently using roughly 3/4 of the energy to complete a race in a time faster than all but the very quickest GT12 cars at our club - compared to the exact same car running a 21.5T 2-pole motor. Properly designed, the suspension will work better as the unsprung weight is halved. These are major advantages and I am not saying my prototype has maximised any of this potential, but the potential is there to be taken and that isn't the case with a conventional geared transmission layout.
__________________
Reply With Quote
  #10  
Old 06-11-2013
Col's Avatar
Col Col is offline
Awesome Admin
 
Join Date: Mar 2006
Location: York
Posts: 4,571
Send a message via AIM to Col
Default

Don't some clubs still run mechanical speed controllers?
If that's the case I expect they will adopt this system in approx April 2213...
Reply With Quote
  #11  
Old 06-11-2013
LongRat's Avatar
LongRat LongRat is offline
Member
 
Join Date: Aug 2011
Location: Bristol, UK
Posts: 240
Default

That's right. Then there are the clubs running tethered cars without radio control at all, they won't go for it either.
Personally I don't understand the MSC runners. Once you factor in a servo and the MSC itself, you could buy an ESC.
__________________
Reply With Quote
  #12  
Old 07-11-2013
westie's Avatar
westie westie is offline
Senior Member
 
Join Date: Dec 2007
Location: Hereford
Posts: 895
Send a message via Skype™ to westie
Default

Very cool!
__________________
LB Racing ~ RCBearings ~ RCDisCo~ SMD
Reply With Quote
  #13  
Old 07-11-2013
SlowOne SlowOne is offline
Mad Member
 
Join Date: Oct 2007
Posts: 1,549
Default

LR - how will we be able to compensate for tyre wear on this set-up, or change gear ratio to suit tighter or more open tracks? It's a clever use of the torque characteristics of a DC motor!
Reply With Quote
  #14  
Old 07-11-2013
LongRat's Avatar
LongRat LongRat is offline
Member
 
Join Date: Aug 2011
Location: Bristol, UK
Posts: 240
Default

There is enough torque to spin up the wheels with this particular motor at low speeds, even with a top speed exceeding the rest of the cars on track by a good margin. I've been running the throttle to 80% so I don't have a crazy speed advantage. I think you might get away with setting up for the biggest track in the country and still have more than enough low end punch for the tightest track. That remains to be seen. Otherwise, rather than changing gearing it would be a case of changing stators. Not a major issue with these complete motors selling for under a tenner each.
__________________
Reply With Quote
  #15  
Old 19-11-2013
mr. ed mr. ed is offline
Senior Member
 
Join Date: Feb 2008
Location: Mechelen, Belgium
Posts: 529
Default

I'm curious how you plan to do a diff on this one. Any chance to see an exploded view: all parts layed out in order before assembly?
Reply With Quote
  #16  
Old 19-11-2013
LongRat's Avatar
LongRat LongRat is offline
Member
 
Join Date: Aug 2011
Location: Bristol, UK
Posts: 240
Default

Quote:
Originally Posted by mr. ed View Post
I'm curious how you plan to do a diff on this one. Any chance to see an exploded view: all parts layed out in order before assembly?
Here's a drawing of the assembly. I'm currently making the parts, hoping to have a running prototype by Friday. It involves making a new rotor with a row of balls built in. Because this style of motor has an external rotor, driven from the outside, it makes turning it into a 'motor diff unit' much simpler.

__________________
Reply With Quote
  #17  
Old 21-11-2013
dodgydiy's Avatar
dodgydiy dodgydiy is offline
Senior Member
 
Join Date: Sep 2008
Location: west wales
Posts: 744
Default

used to have an rc18b with an outrunner integrated into the centre shaft, also have a small drag rail with that setup, it works very well but you do need a higher rated speed control and good batteries because startup currents are VERY high. both are/were very smooth to drive, but very limited by the gearing, or lack of. not too bad onroad with foams i suppose because you can true your tyres to get suitable gearing. by the way, you want a really smooth mardave, try a keda 450h 3200kv outrunner, really good to drive!!
Reply With Quote
  #18  
Old 22-11-2013
LongRat's Avatar
LongRat LongRat is offline
Member
 
Join Date: Aug 2011
Location: Bristol, UK
Posts: 240
Default

Love to see some pics dodgydiy.
But a Keda 3200 on a Mardave? That would be out of control. I doubt many speed controllers that could actually fit in a Mardave could handle those start up currents!
__________________
Reply With Quote
  #19  
Old 22-11-2013
simon simon is offline
Senior Member
 
Join Date: May 2006
Posts: 753
Default

Great idea!...well done.....cant wait to see how it develops...
Reply With Quote
  #20  
Old 24-11-2013
LongRat's Avatar
LongRat LongRat is offline
Member
 
Join Date: Aug 2011
Location: Bristol, UK
Posts: 240
Default



Components for the motor diff unit.
-Motor stator
-303 stainless steel through shaft and ring carrier
-Modified 14-pole rotor
-Acetal ball cage
-Standard Mardave steel diff ring
-6082 aluminium differential hub
-Stainless end cap with stub axle
-End cap mounting screws

I just completed most of the parts. Test fit time.
__________________
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 10:21 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
oOple.com