|
#1
|
|||
|
|||
spur b4
does the spur gear make a noise b4 or should it be smooth ? any help plz . or do all buggy make noise from the spur gear ?
|
#2
|
|||
|
|||
all goes off dp size, but on a b4 should be quiet, sounds to me you havnt got enough clearance between the pinion and spur. or slightly too much (is it stripping the teeth?)
|
#3
|
||||
|
||||
You should also check the gap is consistant by rotating the spur one full rotation, and checking the gap. Not all spur gears are perfectly round so what may seem enough on one side may be tight on the other.
I use a bit of paper or insulation tape between the teeth when I set mine so it cant be too tight.
__________________
My feedback http://www.oople.com/forums/showthread.php?t=19395 |
#4
|
|||
|
|||
i seen a few people that done that in the past but never actually tried it. does it work on 64 dp gears or just the 48dp
|
#5
|
||||
|
||||
i use the paper trick. works every time with 48dp's
should work on 64 dp to, try it ? try a Rizla if not
__________________
Rc18t madrat
|
#6
|
||||
|
||||
If you find paper too thick for the finer 64dp use tissue paper folded.
__________________
My feedback http://www.oople.com/forums/showthread.php?t=19395 |
#7
|
|||
|
|||
WHAT SPUR GEARS ARE THEY 48DP OR 64DP
|
#8
|
||||
|
||||
b4 's are 48dp mate
__________________
|
#9
|
|||
|
|||
THANKS GIRBIL
Last edited by stampede vxlboy; 10-10-2009 at 06:07 PM. |
#10
|
|||
|
|||
i think you should fit the madrat spur and pads on it, that will make it run a bit quieter
__________________
4wd - X4TE 2wd - X2C (Mad Rat passed down to son!) Ansmann Racing UK RIP - MicroTech Racing Trader Feedback |
#11
|
||||
|
||||
madrat spur is socking !
__________________
Rc18t madrat
|
#12
|
|||
|
|||
are you joking jim 76 the spur gears for the madrat are pants
Last edited by stampede vxlboy; 11-10-2009 at 12:20 PM. |
#13
|
|||
|
|||
sorted the spur gear out. but when i hit the brakes it slow at the brakes coming on . using ezrun 5.5 could it be coz of the power of the motor .i need it to stop dead . i use the same set up in my son madrat and the brakes on that are fine but that a ezrun 9turn
|
#14
|
||||
|
||||
Quote:
__________________
DO NOT BUY/SELL TO THIS USER. |
#15
|
|||
|
|||
i have but it will not set like the madrat brakes the well fast . but is that because the motor been faster or not . 5.5turn b4 and the madrat 9turner
Last edited by stampede vxlboy; 11-10-2009 at 12:56 PM. |
#16
|
||||
|
||||
it could just be that you are going allot faster than the 9 turner and u need further to stop
__________________
DO NOT BUY/SELL TO THIS USER. |
#17
|
|||
|
|||
it does not seem it was making a buzzing tune and rev up on its own with out me touch the handset
Last edited by stampede vxlboy; 11-10-2009 at 08:15 PM. |
#18
|
|||
|
|||
no the motor works fine in my son madrat the brakes are fast as hell . but in the b4 its like it takes 10 seconds to stop a little bit. but just rolls in the b4 like it does not want to stop . but the madrat rat as the same esc in a stop fast as hell in madrat but not the b4 . does anybody know why it would do this
|
#19
|
|||
|
|||
any help would be good
|
#20
|
||||
|
||||
Are the rear wheel locking and the buggy just skidding to a stop? If so, that will explain why the B4 takes longer to stop (tyres have maximum braking traction just before they lock up and when they lock up they have less)
__________________
Dragon Paints |
|
|