Go Back   oOple.com Forums > Trade Room > Wanted

Reply
 
Thread Tools Display Modes
  #1  
Old 19-06-2019
breizhator2 breizhator2 is offline
New Member
 
Join Date: May 2010
Posts: 23
Default KC => L1 rear conversion

Hi i'm looking for L1 rear conversion set for Schumacher KC Regards
Reply With Quote
  #2  
Old 19-06-2019
knighthawk's Avatar
knighthawk knighthawk is offline
Mad Member
 
Join Date: Oct 2006
Location: West Wiltshire
Posts: 1,541
Default

You can get the parts to convert

U7613 CVD LD Driveshaft
U7493 Hex 7.5 L1
U7333 Wishbones
U7368 Outboard Pivit Pin L1
U7392 Rear Hub L1
U2698 Hub Bearing
__________________
Schumacher
Speed Passion
Futaba
Support from: My Back Pocket

Driver - 'Derek'
Feedback Link : http://www.oople.com/forums/showthread.php?t=48311
Reply With Quote
  #3  
Old 19-06-2019
mark christopher's Avatar
mark christopher mark christopher is offline
Spends too long on oOple ...
 
Join Date: Jan 2007
Location: haxey, doncaster
Posts: 7,744
Send a message via MSN to mark christopher
Default

Quote:
Originally Posted by knighthawk View Post
You can get the parts to convert

U7613 CVD LD Driveshaft
U7493 Hex 7.5 L1
U7333 Wishbones
U7368 Outboard Pivit Pin L1
U7392 Rear Hub L1
U2698 Hub Bearing
rear hub bearings are the same between kc and ld
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - RCDisco
Reply With Quote
  #4  
Old 20-06-2019
knighthawk's Avatar
knighthawk knighthawk is offline
Mad Member
 
Join Date: Oct 2006
Location: West Wiltshire
Posts: 1,541
Default

Quote:
Originally Posted by mark christopher View Post
rear hub bearings are the same between kc and ld
Cheers Mark,

To be honest I stole the list from another thread
Not owning the conversion myself ( I missed out before they became discontinued )

I was going to get the bits, now know donít need the bearings 🤪
Attached Images
File Type: jpeg 950DD512-736E-4ADC-B76D-99E6B96C203F.jpeg (135.7 KB, 9 views)
__________________
Schumacher
Speed Passion
Futaba
Support from: My Back Pocket

Driver - 'Derek'
Feedback Link : http://www.oople.com/forums/showthread.php?t=48311

Last edited by knighthawk; 20-06-2019 at 05:36 AM.
Reply With Quote
  #5  
Old 20-06-2019
Kevg57 Kevg57 is offline
Member
 
Join Date: Feb 2019
Location: South Wales
Posts: 49
Default

the list depends on the age of the KC.

I had a kit from early this year and it had the L1 hubs and L1 length driveshafts, 67.13mm if I remember correctly.

if you run a roll bar you will need the L1 joints for the lower link to wishbone as it moves from outside the arm to inside the arm.

I did not change my hexes as the original kit did not have them in it, you do need an oring as a shaock bump stop though

original kit had
driveshafts
hubs
arms
orings
c clips spacers
Reply With Quote
  #6  
Old 20-06-2019
tyreman's Avatar
tyreman tyreman is offline
Mad Member
 
Join Date: Dec 2005
Location: Leamington Spa
Posts: 1,882
Default

The conversion kit had Cat SX rear driveshafts in it, you can use the lay down driveshafts but you would need to get the L1 1.5mm hexes.
__________________
LRP, Screwz4RC, Spektrum, Horizon Hobby,
Sanwa, Racer, RichPaint, RDT products,
Trishbits, Bandicoot Bodies

http://www.screwz4rc.co.uk

Reply With Quote
  #7  
Old 20-06-2019
Kevg57 Kevg57 is offline
Member
 
Join Date: Feb 2019
Location: South Wales
Posts: 49
Default

Quote:
Originally Posted by tyreman View Post
The conversion kit had Cat SX rear driveshafts in it, you can use the lay down driveshafts but you would need to get the L1 1.5mm hexes.
I was told by Schumacher you can use the KC driveshafts, you just need to limit full travel with the shock bump stop, they did not mention anything about the hexes, maybe this was because my KC kit came with the L1 rear hubs anyway from new.
Reply With Quote
  #8  
Old 20-06-2019
tyreman's Avatar
tyreman tyreman is offline
Mad Member
 
Join Date: Dec 2005
Location: Leamington Spa
Posts: 1,882
Default

You can use the KC driveshafts but the conversion came with sx driveshafts which is why you didn’t need to limit the shocks, When they ran out of them they discontinued the conversion.
__________________
LRP, Screwz4RC, Spektrum, Horizon Hobby,
Sanwa, Racer, RichPaint, RDT products,
Trishbits, Bandicoot Bodies

http://www.screwz4rc.co.uk

Reply With Quote
  #9  
Old 20-06-2019
breizhator2 breizhator2 is offline
New Member
 
Join Date: May 2010
Posts: 23
Default

If i understand i only need
U7368 L1 rear outboard pivot pin
U7392 L1 rear hub carrier
U7333 L1 rear A-arm
Good ?
Reply With Quote
  #10  
Old 21-06-2019
Npdp72's Avatar
Npdp72 Npdp72 is offline
Senior Member
 
Join Date: Apr 2011
Posts: 319
Default

Iíve got some spare new in pack CAT SX driveshafts if you do want some?
Reply With Quote
  #11  
Old 26-06-2019
knighthawk's Avatar
knighthawk knighthawk is offline
Mad Member
 
Join Date: Oct 2006
Location: West Wiltshire
Posts: 1,541
Default

Just a question on the conversion

Has any one tried the conversion on the KD ?

If so what did you find ?
__________________
Schumacher
Speed Passion
Futaba
Support from: My Back Pocket

Driver - 'Derek'
Feedback Link : http://www.oople.com/forums/showthread.php?t=48311
Reply With Quote
  #12  
Old 26-06-2019
DarkHawk DarkHawk is offline
Senior Member
 
Join Date: May 2014
Posts: 705
Default

Quote:
Originally Posted by knighthawk View Post
Just a question on the conversion

Has any one tried the conversion on the KD ?

If so what did you find ?

I'm just about to put this on my KD so will let you know
__________________
Carten M210R
Xray XB4 18
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 04:25 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
oOple.com