|
#21
|
|||
|
|||
cool, have you thought of making the c hubs too. I would suggest an improvement on the c hubs, increasing the height by 3mm so that ZX-5 knuckles can be used, as well as ZX-5 ball studs, that would help a lot, it would be good to have an option to increase the caster angle also from 5 to 8 degrees for very low grip and rough tracks.
|
#22
|
|||
|
|||
|
#23
|
||||
|
||||
Looking good. I don't know how close the final product will look to the original arms, maybe add a little design twist, so it will always be clear this is a repro-item?
|
#24
|
||||
|
||||
Quote:
I might have to get a set of these in blue. Any chance of doing a Mid front gearbox or LA-26 Lazer wishbones? Is it possible to dye the parts from Shapeways and/or sand the surface smooth?
__________________
___________________ Maxxum FF Ultima Pro Turbo Optima Mid SE Turbo Optima Mid SP Optima Mid Custom Special Lazer ZX Lazer ZX-R Lazer ZX-S |
#25
|
|||
|
|||
Quote:
http://www.ebay.co.uk/itm/3512665475...%3AMEBIDX%3AIT And this filament http://www.ebay.co.uk/itm/2011315206...%3AMEBIDX%3AIT Testing is ongoing.... the resolution is not that great so some final surface finishing is required, but its looking promising. The biggest issue is printing time, to get good resolution prints can take hours.... even for a quite small part |
#26
|
||||
|
||||
That looks brilliant Dan. Do you have the link for it in shapways?
|
#27
|
|||
|
|||
Not showing on there yet.
|
#28
|
|||
|
|||
Small issue with file, surrounding notch between pivots on inboard edge - should get it sorted tonight.
Link to current file - can't yet be printed. https://www.shapeways.com/product/E8...shop-inventory Last edited by Danf1275; 27-02-2015 at 06:17 PM. |
#29
|
|||
|
|||
File now live on Shapeways.
If anyone does try items, please forward any feedback - I don't have an Optima (Schumacher man myself), so have no means to test. https://www.shapeways.com/product/E8...ionId=55960019 Last edited by Danf1275; 27-02-2015 at 08:17 PM. |
#30
|
|||
|
|||
if you can send me the STL file I'll try it on my printer this weekend
|
#31
|
||||
|
||||
Hi Dan,
I've ordered a pair and I'll let you know how they perform. Thanks again for making the file Quote:
|
#32
|
|||
|
|||
No problem - do you want broken original back?
|
#33
|
||||
|
||||
Hi Dan,
no it's OK, just chuck it out. |
#34
|
||||
|
||||
The replacement printed arms arrived today from Shapeways. My first impression is they are very light compared to the original ones. Not sure if this will make them weak but I'll give them a good test in a racing environment and let you all know how they perform. The picture is a close up and they don't look anywhere near as grainy in the flesh.
Optima Mid Arms.jpg |
#35
|
|||
|
|||
Run some test prints on my Home 3d printer and its seems pretty good. I only used PLA for the tests and the only issue I was found was that the current orientation meant that the hinge joints were very weak. This was due to the strand orientation (Not an issue with the kit shapeways uses)
This was fixed buy rotating the piece on the bed |
#36
|
|||
|
|||
I make lots of rc parts on Shapeways for the RC10 and soon the JRX2. I only offer them in white polished. All of Shapeways colored parts are actually white inside with only the outside layer being colored. None of the colored parts is polished. The white polished parts have a much nicer finish to them and they can easily be dyed to any color. Printed parts take dye very well and just soak it up like a sponge so scratching them doesn't easily result in white showing through.
|
#37
|
|||
|
|||
nice to see you are on here too fred !
|
#38
|
|||
|
|||
A friend of mine just bought a couple 3d printers and offered to print me a part or two. Would someone mind sending me the file? It will be a while before I can try it on a car as all my r/c is in storage but i will post a pic once it's printed and share any details from my friend about the printing process itself. Thanks!
|
|
|