|
#2
|
||||
|
||||
Batley Outdoor
Springs: 6t Pistons: Hard + Valve Oil: 35 Associated Toe: In 1 Degree Camber: 2 Degrees Castor: 0 washer behind wishbone Ground clearance: 16mm Anti Roll Bar: None Rear: Springs: 5.5t/Gold Pistons: Two hole, no groove Oil weights: 50wt Associated Toe-in per side: 3 Degrees Camber per side: 2 Degrees Ground clearance: 22mm - or a little more if it cuts up. Anti-roll bar: None Rear lower upright: Upper Hole Damper pickup point: Middle
__________________
Matt Myers Team Associated b4 Team Associated b44 |
#3
|
||||
|
||||
Worksop Indoor
Front 6 turn springs Kit pistons & rebound valves 30 wt oil Push rods mounted on top of rockers 0 degree toe in - may need 1 deg toe-out -1 degree camber Castor - right back 14mm ride height - or lower at Worksop depending on bumps, but ride height has a big influance on steering on the Pred as you probably know. Rear 5 1/2 turn springs & pre springs Kit pistons 45 wt oil Middle hole rockers 4 degrees toe-in per side -1 degree camber 22mm ride height - or lower at Worksop, but drop front and rear the same.
__________________
Matt Myers Team Associated b4 Team Associated b44 |
#4
|
||||
|
||||
Southport Outdoors
Front 5.5 turn springs Kit pistons & rebound valves 30 wt Losi oil Kit rockers (push rods mounted on top) 1 degree toe in -2 degree camber Castor – 4 washers in front, 3 behind Front pushrod length - 30mm 16mm ride height Rear 5 1/2 turn springs & pre springs Kit pistons 50 wt losi oil Middle hole rockers 2 degrees toe-in per side -2 degree camber 22mm ride height Maximum Droop Kit Anti Squat [Courtesy of Peter Ellis]
__________________
Matt Myers Team Associated b4 Team Associated b44 |
#5
|
||||
|
||||
Coventry Outdoors
FRONT: Caster: 5 washers back, 1 forward Push rod placement: mounted on top of the rocker. Roll-bar: none toe in: 1degree ride height: 18mm camber: 2degrees Springs: 5.5t black Oil: Associated 35wt pistons: kit 1 way unit in the front, fixed prop shaft. REAR: Roll bar: yes- soft setting. Toe in: 2degrees ride height: 23mm camber: 2degrees Anti Squat: 3.5 degrees Shock pick up position: middle hole hub pick up position: upper hole springs: 6.5t black Oil: associated 30wt. Pistons: 2 hole - kit [courtesy of Tom Yardy]
__________________
Matt Myers Team Associated b4 Team Associated b44 |
#6
|
||||
|
||||
Southport Outdoors By Tom
Front
6 turn springs Kit pistons & rebound valves 35 wt associated oil Kit rockers (push rods mounted on top) 1 degree toe in -1 degree camber Castor – 4 washers in front, 3 behind Front pushrod length - 30mm 16mm ride height tyres: worn yellow mini spikes Rear 5.5 turn springs & pre compression springs Kit pistons 50 wt Schumacher oil Middle hole rockers 1 degrees toe-in per side -1 degree camber 22mm ride height Kit Anti Squat 3mm droop Tyres: worn yellow mini spikes Nosram evo 2007 with 6.5 Spur 72t Pinion 19t IB 4200 cells
__________________
SEX11 - Probably the fastest car in the World in it's class! http://www.teamxtreme.co.uk |
#7
|
|||
|
|||
Might be useful having the type of track, track conditions etc on each setup otherwise people wont know what type of track the setup is for.
|
#8
|
||||
|
||||
dito
|
#9
|
|||
|
|||
Quote:
hi guys... that my set-up for southport... southport is a mixture of surfaces, mainly astro and grass with a couple of othe sections made up of cobbles, tarmac and concrete.. this set-up was used on a dry and sunny day, with plenty of grip on the track, however it does also work well in damp conditions as it makes the car a little less likely to suffer from grip role etc.... hope this helps Tom
__________________
Team Losi Racing, Horizon Hobby TLR 22 5.0, TLR 22X-4, TLR 22-4, 22-4 2.0 Atomic Carbon S2, S44, Vega B4.1 Trader feedback: http://www.oople.com/forums/showthread.php?t=19374 |
#10
|
||||
|
||||
here is a starting point for the new shocks on the x11 working both on flat grass and epr as well
front springs blue (no compreision spring) 5 1/2 turn in older style oil 25wt losi piston kit with standard rebound valve pushrod above rocker pushrod lenth 33mm with shockball undone 1turn revised front arms with 1 washer behind wishbone cone washer replaced with 4 losi gold ballstud washers. 2 under outer ball with 2 above extra midde hole drilled for roll bar roll bar 1.2mm (standard) middle hole ride height 19-20 mm front wing kit with standard lines followed slight toe out with 2 degrees of camber rear springs blue (no compresion spring) 5 1/2 turn in older style oil 30-32.5 losi(depending on jumps) piston kit lower hole on shock mount roll bar 1.2mm again in middle hole in lowered position (pic to follow) wheelbase lenthened 1mm ride height 22mm 1.5mm rear block (reduces on power steering) large rear wing with full guerney toe in to middle of front wheel rear uprite in upper hole shumacher yellow minispikes with outside outer row cutoff rear and 2 inner and outer cut off front any extra info you need feel free to ask or pm Nathan
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams woop woop racing officialy keeping team toe out inline Last edited by niggs98; 12-06-2008 at 08:48 AM. Reason: to keep everyone happy about the bits i missed lmao |
#11
|
||||
|
||||
thx
what is "epr"? and what can the Blue spring be compared at, in terms of the old springs? |
#12
|
||||
|
||||
epr is eden park raceway (high bite astroturf and multi surface track) the springs now come colour coded so i will find out the turn equvalent when i get home but they are 1 down from stiffest
hth
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams woop woop racing officialy keeping team toe out inline |
#13
|
|||
|
|||
lower hole on rear hub or shock mount rocker?
__________________
RC US Imports - Sworkz USA- Maclan Racing- Bellgate Distributors. |
#14
|
||||
|
||||
I *think* the blue spring would be the 5 1/2 turn 1.3mm spring
G
__________________
Graham North http://www.atomic-carbon.co.uk https://www.facebook.com/atomiccarbon https://www.facebook.com/nortechracing |
#15
|
||||
|
||||
He means on the rear rocker
Just noticed he forgot to mention the rear upright hole G
__________________
Graham North http://www.atomic-carbon.co.uk https://www.facebook.com/atomiccarbon https://www.facebook.com/nortechracing |
#16
|
||||
|
||||
setup eddited for the above questions
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams woop woop racing officialy keeping team toe out inline |
#17
|
|||
|
|||
Where did you adjust the wheel base?
|
#18
|
|||
|
|||
Oh and is that how you ran it on Sunday at the regional?
|
#19
|
||||
|
||||
i add washers inbetween the front of the rear hub and the ball joint adam and i tried it in the last final at the regional just to give a little more pivot. tested it again at epr yesterday in the dry and found it to be good with the full set up shown
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams woop woop racing officialy keeping team toe out inline |
#20
|
|||
|
|||
Hi its Adam. I've realized that by doing that you are reducing the hub anti-squat too. I've worked out that by adding 2MM it will make the hub and the wishbone parallel. While also making the wheelbase 2MM longer. I wish i had thought about on Sunday as i think that would have improved my car on the dusty section going onto the straight. You car seemed really stable there and i think this could explain it, do you agree? Will definitely try it next time we're at a track. I think i will also find a way of adjusting the top wishbone as we talked about so that i can change the anti-squat and the wheelbase independently.
|
|
|