oOple.com Forums
Page 1 of 2 1 2
Show 40 post(s) from this thread on one page

oOple.com Forums (http://www.oople.com/forums/index.php)
-   Team Durango (http://www.oople.com/forums/forumdisplay.php?f=80)
-   -   dex210 front wheels (http://www.oople.com/forums/showthread.php?t=83019)

jonathan may 13-10-2011 07:19 PM
dex210 front wheels
 
so i i assume that the 210 front wheels should be in stock sometime next week with the next batch of 410v3,s ?

Matt Howard 13-10-2011 07:29 PM
anyone know if the TRF201 front wheels can be used?

stegger 20-10-2011 07:14 AM
http://www.deracing.net/store/index....y&path=130_150

DERACING are doing wheels ;)

AmiSMB 20-10-2011 11:00 PM
Quote:
Originally Posted by Matt Howard (Post 566474)
anyone know if the TRF201 front wheels can be used?
TFR201 wheels fit but you need to a 2mm wide spacer before the inner bearing so they match up with the end of the axle.

sunbeam 20-10-2011 11:15 PM
Yuck, whats with the rivets ?

jonathan may 22-10-2011 02:08 PM
what way do people mount schumacher stagger cut on the 210 front wheel narrow and cut the wheel down or on the whole wheel.

Big G 22-10-2011 02:30 PM
run a stanley knife around the inside against the lip. After several rotations you'll find the blade will go through the rim and you can finish off the cut.

that's how I did it.

jonathan may 22-10-2011 02:50 PM
sorry what i ment was should they be fitted narrow or wide

mattybucks 22-10-2011 02:55 PM
Stagger rib no insert and narrow.
Cut stagger wide with and insert.

ASKay 25-10-2011 05:27 PM
any word on when the Durango DEX210 fronts are arriving to purchase?

sunbeam 25-10-2011 05:30 PM
Any news on spares, full stop ?

triplesix 25-10-2011 08:02 PM
Anyone who managed to fit Schumacher wheels/TD bearings in those?
No TD wheels available at my place and there's a race in 10 days, so I'll try to use the ones I have... :blush:

neil_p 25-10-2011 08:23 PM
I'm positive it has been mentioned in a previous post that a front axel that would accept Schumacher/AE front wheels would be available, I just cannot remember which post it was in, or weather it would be from Durango or another company.

If that person can confirm?

bodgit 25-10-2011 08:39 PM
Was it this by Adam
http://www.oople.com/forums/showthre...371#post569371

Wheels are due in next week.
You can 'Drill / Ream' a B4 wheel out to 10mm and then press in the Durango bearings. It will help get you away until you get the proper ones :)

sunbeam 25-10-2011 08:45 PM
I can CONFIRM that Schumacher and AE front wheels DO NOT FIT. The 210 bearings are to big for the Schumbacher and AE wheels. The front axles on the 210 are to big for the Schumacher and AE bearings.

bodgit 25-10-2011 09:03 PM
Quote:
Originally Posted by sunbeam (Post 572668)
I can CONFIRM that Schumacher and AE front wheels DO NOT FIT. The 210 bearings are to big for the Schumbacher and AE wheels. The front axles on the 210 are to big for the Schumacher and AE bearings.
Thats why Adam recommended reaming out AE wheels to fit TD bearings as a temporary solution.

neil_p 25-10-2011 09:06 PM
Nah it wasn't that post from Adam.

Like I said I cannot remember and I'm not going to wade through all the posts. All I can imagine is it will be a Schumacher/AE sized axel with the Durango fitment. If no one will do one I'll fabricate up a couple.

ASKay 25-10-2011 11:16 PM
I was looking at getting some made, but then decided I like TD wheels too much, so resided myself to buying new tyres, and wheels.....

just means i will be racing 4WD this weekend...

Dazzler 25-10-2011 11:23 PM
Quote:
Originally Posted by neil_p (Post 572660)
I'm positive it has been mentioned in a previous post that a front axel that would accept Schumacher/AE front wheels would be available, I just cannot remember which post it was in, or weather it would be from Durango or another company.

If that person can confirm?
Is this the post you are looking for...

http://www.oople.com/forums/showpost...0&postcount=46

And you could fit 201 wheels with some shims fitted to the stub axle first.. Might be easier for some prior to the release of these..

neil_p 26-10-2011 05:53 AM
That's the one Dazzler.

I agree the Duango wheels are better but got loads of Schumacher slims that I like to run and I don't like to cut the wheels down. Unless Durango are prepared to make a slim wheel I'll run the Schumacher ones.

Same for the rears, got loads of pin type wheels, so will run the optional cone washer and spacer for the time being.

mikeyscott 26-10-2011 07:42 AM
Quote:
Originally Posted by neil_p (Post 572752)
That's the one Dazzler.

I agree the Duango wheels are better but got loads of Schumacher slims that I like to run and I don't like to cut the wheels down. Unless Durango are prepared to make a slim wheel I'll run the Schumacher ones.

Same for the rears, got loads of pin type wheels, so will run the optional cone washer and spacer for the time being.
Neil,

Have you enlarged the Schumacher wheels yet?

Got your PM, that would be cool. I'll confirm tomorrow if that's ok, just got an issue on the car I'm trying to get to the bottom of.

Mike

mark christopher 26-10-2011 09:12 AM
Why not just machine the front axle to take the b4 bearings?

neil_p 26-10-2011 11:12 AM
Hi Mike, not a problem, just let me know what you want to do.

Not going to enlarge the wheels as at least then I can swap between the two cars.

Mark, havnt had the chance to measure up yet, but if I'm going to trim down the axel in the lathe then its just as easy to make new axels, and then I have them for the Durango wheels if I so wish. I imagine that the axel diameter on the AE types is smaller as the axel is steel and the Durango is alloy, but only assuming.

4_cell_racer 26-10-2011 06:11 PM
Quote:
Originally Posted by neil_p (Post 572752)
Same for the rears, got loads of pin type wheels, so will run the optional cone washer and spacer for the time being.
Can I ask what the part numbers are for the spacer & cone washer?

mikeyscott 26-10-2011 06:12 PM
Quote:
Originally Posted by 4_cell_racer (Post 573034)
Can I ask what the part numbers are for the spacer & cone washer?
Wheel Cone Rear TD714002
Wheel Distance Bushing Aluminium 6x5x1.5mm TD712003

mark christopher 26-10-2011 06:43 PM
Quote:
Originally Posted by neil_p (Post 572858)
Hi Mike, not a problem, just let me know what you want to do.

Not going to enlarge the wheels as at least then I can swap between the two cars.

Mark, havnt had the chance to measure up yet, but if I'm going to trim down the axel in the lathe then its just as easy to make new axels, and then I have them for the Durango wheels if I so wish. I imagine that the axel diameter on the AE types is smaller as the axel is steel and the Durango is alloy, but only assuming.
rough measurment durango is 5mm )going by bearing size) associated is 4.75mm, i plan on getting a spare set of axles and machining them (my associated ones are alloy)

neil_p 26-10-2011 06:55 PM
Hi Mark, nice one for measuring up.

Since AE changed to steel from alloy for their axels, I am going to make a set up in either chromoly or stainless. Could do them ti but I reckon steel will be more than up to the job.

Durango have probably used 7000 or 6000 series aluminium up to T6 so imagine they are strong enough, let us know how they hold up Mark, when the spares get released:woot:

4_cell_racer 26-10-2011 07:42 PM
Quote:
Originally Posted by mikeyscott (Post 573035)
Wheel Cone Rear TD714002
Wheel Distance Bushing Aluminium 6x5x1.5mm TD712003
Cheers Mikey :thumbsup:

Chris-S 27-10-2011 02:01 PM
Front wheels are in stock!

mikeyscott 27-10-2011 02:35 PM
Chris you at TORCH Sunday?

Chris-S 27-10-2011 02:45 PM
Depends on the weather. Will probably run the 210, waiting on some shiny bits for the 410

Big G 27-10-2011 02:59 PM
Quote:
Originally Posted by Chris-S (Post 573363)
Front wheels are in stock!
indeed. I saw the stock level drop by 250 in the 1st 20mins haha

mikeyscott 27-10-2011 03:01 PM
Quote:
Originally Posted by Big G (Post 573388)
indeed. I saw the stock level drop by 250 in the 1st 20mins haha
What on TDs site? Bloody hell, gold dust at this rate!

gainsy 27-10-2011 03:03 PM
MB Models have white ones :D or had some a few minutes ago when i ordered some & some front wishbones :)

jamiekerr14 04-11-2011 01:56 PM
Hi chaps, I have got some New tyres and rims for my 210 that is coming next week. And got some Cut Stagger ribs, how have people mounted them on there 210 wheels.

Im mainly racing at Torch-High grip astro

I have heard so many way on mounting them, and inserts or no inserts. Anyone care to tell me more on that stuff. Sorry-Never run a 2WD mainly a 4WD person, so have no clue! cheers fellas!:thumbsup:

gainsy 04-11-2011 02:23 PM
Personally i have cut the wheels down so the staggers fit properly as i found the front wheels too wide to stretch the tyres across, didn't have this issue with mini spikes though
No inserts for me :)

jamiekerr14 04-11-2011 02:28 PM
Yeah I have 1 wide 1 narrow on the rim. The narrow one seems to have a better profile from what I can tell.

mattybucks 04-11-2011 02:29 PM
I have loads of wheels and towers in stock if anybody needs any.

Matt Butcher 04-11-2011 02:52 PM
for normal staggers mount on cut down wheels with no insert, for cut staggers mount on normal sized durango 2wd wheels.

job done :)

mattybucks 04-11-2011 02:55 PM
Quote:
Originally Posted by Matt Butcher (Post 577274)
for normal staggers mount on cut down wheels with no insert, for cut staggers mount on normal sized durango 2wd wheels.

job done :)
for cut staggers mount on normal sized durango 2wd wheels. - with an insert.


All times are GMT. The time now is 09:21 PM.
Page 1 of 2 1 2
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2026, vBulletin Solutions, Inc.
oOple.com