View Single Post
  #9  
Old 19-07-2017
nerius nerius is offline
New Member
 
Join Date: Apr 2007
Posts: 25
Default

All ten 1/8” diameter suspension hinge pins are made of titanium grade 5 alloy and were machined by me on a lathe. The diameters are about two hundredths of a millimeter thicker than the standard 1/8” which provides a tighter fit on older cars with sloppy and worn out suspensions. The surface of the hinge pins was ground with a 1500 grit sandpaper for smooth rotation in suspension. The notches in hinge pins have a slightly tighter 0.5 mm or so width and as a result the suspension hinge pin e-clips fit more securely (diameter for e-clip seating being the same).

The conical washer used on the outside of the rear axle next to roll pin is Associated part #6388. Four come in each package. I think that the instructions tell you to use just one per side, leaving enough in one package for two cars. Well, I used two packages. I’m using four conical washers per side, oriented in the same direction. This left a tiny bit of play in the rear axle bearings as a result. Furthermore, four conical washers offer more strength in extreme cornering with extreme side forces being put on the rear axle. Four won’t crush as easily as one. Thin conical washers are springy in nature and I don’t want them to compress and/or deform while the vehicle is being used. Stacked together they can be used as shims. Note to self: try using angular contact bearings on larger cars.

You can see the titanium machining on the ends of the hinge pins in both photos above. The steering knuckle hinge pin has black nylon washers above and below caster block. This is the way the original was designed (although they used white instead of black spacers). I left the lengths and distances between e-clips as original as possible on the revised hinge pins.

The way that the front structural tubes are attached to the chassis makes me cringe a little bit, especially considering that these screws used by me aren’t made of steel (they’re 7075-T6). There seem to be angles involved and the chassis material seems to demand to be bent to get a tight fit. I inserted nylon washers, black in photo, in front of and behind the front chassis nose plate, in order to provide a little bit of “crush cushion” because the tightening of these screws became a bit uncomfortable. It was probably a mistake not to use the original steel alloy screws (readily available at any U.S. hardware store) in this particular spot. However, the aluminum screws are holding well and don’t seem to be close to breaking or close to severe distortion. What happens in an impact is a different matter however.

The shocks, front and rear, were completely overhauled, including the bottom seal. The only part not re-used was the internal housing ring that holds the red o-rings and such in place at the bottom of the shock body. Again, I assumed that by taking these off it’s not possible to not bend them such that they become deformed. A hardware store in the U.S. will typically sell 5/16” internal housing rings, which is exactly the part I’m using for this clamp. They’re one size smaller than the internal housing rings used to hold the ball bearings in place in the gearbox outdrive halves. They match the original parts that came in the Associated kits.

To seal the shocks caps I’m using 1 mm thick black o-rings also purchased from the hardware store. This o-ring seal was apparently an “upgrade” back in the day. The original fiberglass-like seals are still in great shape, and have been put away in a small ziplock bag. It’s amazing how many RC10 parts this hardware store has! They even have the exact rear axle roll pin I’m looking for! The o-ring for sealing the shock cap to shock body should be chosen such that it’s the smallest diameter o-ring that still fits reasonably over the shock body after being stretched on. 1 mm for the o-ring thickness seems to be the perfect thickness and is the thinnest the hardware store had. I found out that sealing shocks with an o-ring is very unforgiving and will make that seal bombproof. I tried forcefully pushing a sealed shock all the way in when not enough “bleeding” had been done, and guess what… the bottom seals busted out. In other words, hydraulic mechanical advantage can be a very powerful tool. The force from the compression of shock oil caused the bottom seals to start rupturing, while the shock cap exhibited zero oil leakage. Long story short… don’t force the shock piston in when you seal the shock with an o-ring! Bleed the shock with shock cap loose first! I managed to repair the seals on the busted out shock. No permanent damage occurred.

I’m also using a black o-ring at the bottom of the shock, between bottom spring cup and shock body, inserted on shock shaft on the outside of shock, visible in some of the photos. These can be cut off with a razor blade without any disassembly if they prove to be useless. The reason for these is that I wanted them to touch the bottom of the shock body at the same time that the shock shaft hits the shock cap internally, when the shocks “bottom out”. I noticed that inside the shock cap there is a cylindrical surface machined specifically for allowing the shock shaft to hit when the shock shaft is fully in. You might hear a metallic “smack”, especially in the rear shocks, when the suspension bottoms out. The o-ring is meant to touch the bottom of shock body just slightly before the shock shaft bottoms out, to cushion the shock smacking just a bit. It also presses in on the bottom seals, which may or may not be a good idea. It may help to press in on the bottom seals once in a while to make sure everything there isn’t “popping out”, kind of like what happened when I erroneously forced the shock shaft all the way in before the shock had been bled properly. I made sure that not much pressure is applied by the o-ring in this spot before the shock shaft hits the shock cap. This is only an issue in the rear currently because on the front suspension the A-arms hit the fiberglass shock tower before the shock has a chance to bottom out. Black cushioner o-rings are present on all four shocks however.

(Continued in next post.)
Attached Images
File Type: jpg conical-washers.jpg (778.2 KB, 5 views)
File Type: jpg front-structural-bars.jpg (721.7 KB, 3 views)
File Type: jpg from-rear-diag.jpg (938.2 KB, 5 views)
Reply With Quote