|
||
|
 |
|
||||||||||||||||||
|
|
|
#1
14-01-2013
|
|||
|
|||
AE FT VTS Sipper Conversion on a DEX210?
I'm always glazing the good AE slipper pads when I run on carpet?
Has any one rigged up the AE VTS slipper on a 210 yet? http://www.amainhobbies.com/product_...Conversion-Set
__________________
Great Hobbies, NRC raceway. 17 years of racing RC see me race http://www.youtube.com/user/myusernameck 
|
|
#2
23-01-2013
|
|||
|
|||
|
Maybe Avid will get on making one?? If I run on really high bite carpet I fight with my slipper all day!
http://www.avidrc.com/product/5/acce...ccesories.html
__________________
Great Hobbies, NRC raceway. 17 years of racing RC see me race http://www.youtube.com/user/myusernameck
|
|
#4
23-01-2013
|
||||
|
||||
|
I run the HT pads on a mix of carpet, astro, rubber matt, painted wood and floor boards. The pads hold up fine to the torment of the different surfaces and have been installed now for a good 2 months without issue. Go HT !
__________________
If you have trader feedback for me please go to http://www.oople.com/forums/showthread.php?t=120160 - Thanks Currently utilising (abusing) Durango DEX210 / KO Propo Espritt III / Tekin / LRP / SpeedPassion / Savox
|
|
#5
23-01-2013
|
||||
|
||||
|
Im up for this as well on my 210, I use it on my lazer ZXR and is superb but will be a bit of a job to do. Maybe a good idea if whoever does design it to make the layshaft thicker in the area where the collar is inside the gearbox. I would be up for buying that.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS
|
|
#6
23-01-2013
|
||||
|
||||
|
I just jun the HT AE Pads, if I fancy a change I may look at the Vented disks which I used on my X6.
__________________
Aidan Burke - Southport Radio Car Club #SchumacherFamily #TQmodels #ExtraLapRCpodcast
|
|
#7
23-01-2013
|
||||
|
||||
|
Actually thinking about it all that is needed is a fractionally longer screw and a slightly wider gear cover and its done. Anyone have any ideas on how to source a screw pretty much identical to the original but fractionally longer? Has to be of the same material.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS
|
|
#8
23-01-2013
|
|||
|
|||
|
I run the vented disks and AE pads. If I run on low bite carpet or dirt its fine. But if I run on really high bite carpet it will be okay for a few packs, then start to glaze! Then I'll be messing with it all day.
Here's a video of the high bite carpet we have in Canada. There's also video's on my page that I run on carpet like the Euro series and my slipper is fine there! http://www.youtube.com/watch?v=gwCMp...y6fANg&index=3 I think it comes down to running on high bite or low bite
__________________
Great Hobbies, NRC raceway. 17 years of racing RC see me race http://www.youtube.com/user/myusernameck
|
 |
|
|
Team Durango
Hybrid Mode
