|
|||||||||||||||
|
|
|
#1
|
|||
|
|||
|
Hi there, I'm interested to hear what people are doing to their cars when running LiPo's?
1. Suspension 2. Weight 3. Other |
|
#2
|
|||
|
|||
|
Not sure if it is worth messing around with lipos in a b44 yet cos I understand that saddle lipos will not be legal for the nationals so until they are the top guys might not bother
|
|
#3
|
||||
|
||||
|
so read his post again he is asking about a B4 not a B44
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD |
|
#4
|
|||
|
|||
|
Do appologise that's what happens when you're boss is around
|
|
#5
|
|||
|
|||
|
Myself and afew friends at our local switched from NiMh's to LiPo's and strangely enough the general feeling is that running LiPo's without the extra weight makes the car handle/feel better than when running LiPo with the extra weight.
This presumes that you are already running the 'lead behind the bulkhead', but otherwise we are running no extra weight and find the car very much planted. Prehaps its something to do with reducing the 'penduleum' effect? Dunno..but it sounds fancy ![]() Or...do what I did and buy an S2 lol
__________________
Previously: BRCA Micro Section Chairman. BRCA Micro National Champion. Currently: JQ fan. Bellend. Forums are better than Facebook groups |
|
#6
|
||||
|
||||
|
I run with the set up in this thread
http://www.oople.com/forums/showthread.php?t=15133 but run around 100 grams with lipo plus the extra weight in the bulkhead |
|
#7
|
|||
|
|||
|
So it's been a while now. Anything new people are doing now.
Most people I talk to just add weight to get it back to 4200NiMh weight. |
|
#8
|
|||
|
|||
|
1mm thick lead plate that matches the length and width of my Trakpower 4900, battery on top all topped off with a shortened battery strap (cos it doesn't slide under the rear bulkhead now). Car has no other lead on it and the suspension is left alone. It's mint now. Pre-lead it just felt way too light, like it was going to float off the track or something.
|
|
#9
|
||||
|
||||
|
all I have done is added 25g lead behind the battery and this seems to work very well with my 4900mAh lipo
__________________
Matt Myers Team Associated b4 Team Associated b44 |
|
#10
|
|||
|
|||
|
I have a 1mm lead plate under a Trakpower 3600 and the Tristbits brass antisquat block in my B4, setups are the same as nimh.
I tried to get it working without extra weight, it does handle better but you go everywhere on your rear wheels! |
|
#11
|
||||
|
||||
|
Does the TP3200 saddle fit in a B4?
|
|
#12
|
||||
|
||||
|
yes it's a direct fit
__________________
Custom MG-Racing Associated DMS |
|
#13
|
||||
|
||||
|
[QUOTE=Richard Lowe;189159]I have a 1mm lead plate under a Trakpower 3600 and the Tristbits brass antisquat block in my B4, setups are the same as nimh.
I tried to get it working without extra weight, it does handle better but you go everywhere on your rear wheels![/QUOTE] Thats the sounds like the problem ive been having running LiPos and brushless, on an indoor polished floor (gym/hall) my B4 just keeps wheel spinning and dough nutting all the time, its very hard to accelerate without spinning out all the time even in a straight line, so i went back to using a brushed motor and Nimh batteries and it made all the difference to handling cos i could put the power down without spinning out.................My LiPos ar a tight fit under the battery strap so think the only way i could put a lead plate under the LiPo would be to file a bit of the bottom of the shock tower to make it fit !!! What other weights/parts would you all suggest so i can use my brushless, LiPo setup ??? ![]() ![]() cheers |
|
#14
|
|||
|
|||
|
@Dexter - I've got a 66g Rudebits brass weight under my lipo, but had to
raise the screws to fit the battery bar in for my bigger lipo's. Get some car wheel weights and get at least 10g each side on the rear of the chassis using the small 5g weights, in the section behind the speedo and receiver. Also, you can put some along the battery bar, not brilliant, but I see it a lot and it works. I've got around 130g on the car at the rear, plus a ghea brass bulkhead which stops it wheelieing. My son has some of the 5g weights around the servo too. Oh, and don't just look at weight (although that will help immensely), experiment with slipper settings and shock setups...squat settings can really help, as can wheelbase. |
![]() |
|
|