Go Back   oOple.com Forums > Car Talk > Schumacher

Reply
 
Thread Tools Display Modes
  #1  
Old 16-05-2010
martin martin is offline
Member
 
Join Date: Jun 2008
Posts: 18
Default Cougar Diff

There are a few people on this forum that appear to be having troubles with thier diffs coming undone, one reason for this to happen is that the internal circlip has popped out of its groove and has caused the thrust race to tilt over and it grips the screw and undoes. however when you undo the diff the load is released from the circlip and it pops back into place, giving the illusion that it has not moved. this circlip must be assembled very carefully each cougar kit had an instruction sheet showing how we recommend this is done. you have to ensure that the sharp side of the circlip is against the washer carrier, slightly open the circlip before you assemble it and place one corner of it in the groove of the washer carrier and push the other side in while squeezning it as little as possible. when the circlip is in the groove it must be tight and difficult to move, if it rotates freely or has some side to side movement remove the clip and try again.
Reply With Quote
  #2  
Old 16-05-2010
DCM's Avatar
DCM DCM is offline
Spends too long on oOple ...
 
Join Date: Oct 2005
Location: Marvelous South Wales!!
Posts: 8,896
Default

Sorry, as the circlip is a general engineering item, if you are having to expand the circlip before placing in, then either the bore or the groove the circlip sits in is to large, or both.
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man!
Reply With Quote
  #3  
Old 16-05-2010
bigred5765's Avatar
bigred5765 bigred5765 is offline
Lion-O - King of the Thundercats
 
Join Date: Mar 2006
Location: chorley
Posts: 8,474
Send a message via MSN to bigred5765 Send a message via Skype™ to bigred5765
Default

it's nether of the above to be honest dcm, the main problem is when people over crush the clip to install it,
__________________
Mattys the driver,my names carl
Reply With Quote
  #4  
Old 16-05-2010
Smartalec's Avatar
Smartalec Smartalec is offline
oOple Advertiser
 
Join Date: Oct 2006
Posts: 1,508
Default

Quote:
Originally Posted by bigred5765 View Post
it's nether of the above to be honest dcm, the main problem is when people over crush the clip to install it,
The point being Carl that if the circlip was the correct fit it wouldn't have to be opened up. A proper circlip should spring back to the correct size after compression, if it's made of monkey metal then it's not man enough for the job. You have to compress it to install it, you should be able to use a pair of circlip pliers and just pop it in, job done
My advice to anyone with a cougar is to source a decent circlip of the correct size before building the diff
Reply With Quote
  #5  
Old 16-05-2010
David Church's Avatar
David Church David Church is offline
*SuPeRsTaR mEmBeR*
 
Join Date: Aug 2006
Location: Trelleborg, Sweden
Posts: 3,320
Default

Quote:
Originally Posted by Smartalec View Post
The point being Carl that if the circlip was the correct fit it wouldn't have to be opened up. A proper circlip should spring back to the correct size after compression, if it's made of monkey metal then it's not man enough for the job. You have to compress it to install it, you should be able to use a pair of circlip pliers and just pop it in, job done
My advice to anyone with a cougar is to source a decent circlip of the correct size before building the diff

But you drive a halfbreed???
Reply With Quote
  #6  
Old 16-05-2010
Smartalec's Avatar
Smartalec Smartalec is offline
oOple Advertiser
 
Join Date: Oct 2006
Posts: 1,508
Default

Quote:
Originally Posted by David Church View Post



But you drive a halfbreed???
Yep, and both halves work
Reply With Quote
  #7  
Old 16-05-2010
bigred5765's Avatar
bigred5765 bigred5765 is offline
Lion-O - King of the Thundercats
 
Join Date: Mar 2006
Location: chorley
Posts: 8,474
Send a message via MSN to bigred5765 Send a message via Skype™ to bigred5765
Default

Quote:
Originally Posted by Smartalec View Post
The point being Carl that if the circlip was the correct fit it wouldn't have to be opened up. A proper circlip should spring back to the correct size after compression, if it's made of monkey metal then it's not man enough for the job. You have to compress it to install it, you should be able to use a pair of circlip pliers and just pop it in, job done
My advice to anyone with a cougar is to source a decent circlip of the correct size before building the diff
thats right and most people do just that and have no problem, but when you squash it shut twice as fare as it needs to be, (and before you say it yes i watched someone rebuilding one and was horrified at how far they crushed it before they fit it),somethings going to give, i have never had to stretch ares and (touch wood) never had a problem with it,
__________________
Mattys the driver,my names carl
Reply With Quote
  #8  
Old 16-05-2010
DCM's Avatar
DCM DCM is offline
Spends too long on oOple ...
 
Join Date: Oct 2005
Location: Marvelous South Wales!!
Posts: 8,896
Default

Think it is a mix of overly generous tolerance on the groove, cheap circlips and a stupid arse design for a diff outdrive to be honest. Every single ball diff I build has a blanked end on each for the spring and the thrust race, so why Schumacher think that having Monkey Mechanics fit a sprung part is better, flumoxes me.... none of these issue's would appear if they run 'normal' design outdrives...
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man!
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 01:08 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2026, vBulletin Solutions, Inc.
oOple.com