|
||
|
 |
|
||||||||||||||||||
|
#1
22-05-2010
|
||||
|
||||
Losi rim on AE axles??
Hi, I have a little conversion in mind, I have a set of losi truck rims and wondered if anyone knows if the fronts will fit on either a b4 or t4 front axle??
 - I have bearings that fit the wheels if these are any use? I know the rears are no problem, got them on.
__________________
Team EDNA Racing!  Hpi Savage 4.6 + innovative RC big bores & LCG chassis! - Savage 25 - Procat - Durango DEX410R - Mardave Banger x2 & carbon GT12 - Tamiya mwb & swb minis - Playmobile caravan! - cut'n'shut TL-01 - Rovan 1/5 Baja 26cc - SCX10 Defender 90 - Venom Creeper - Schumacher Mi5 - Axial Exo buggy x2 -Tamiya Hornet/Baja bug hybrid - Associated SC10 !!! Frsky 2.4ghz !! How many is too many?? 
|
|
#2
22-05-2010
|
||||
|
||||
|
im sure they will work, just give it ago m8
__________________
Sworkz S350 BE1 EU - Tekin RX8 G2 - Tekin T8 G2 1900kv - Xpert SI-4531 BLS Yokomo B-Max2 MR ver2 Factory - Vampire SR1 - Vampire Type AB+ v2 7.5t - Savox SC1251 TLR 8ight T 2.0 Tekno - Tekin RX8 G2 - Tekin T8 G2 1700kv - Savox SA1283SG TLR SCTE 2.0 - Tekin RX8 G2 - Tekin Pro4 4600kv - Xpert SI-3401 BLS LC Racing EMB-1 & EMB-SC Sanwa MT4 Intellect & Gens Ace Powered
|
|
#3
24-05-2010
|
||||
|
||||
|
think what i mean was the rims look deeper than the b4 axles length, is it worth me getting the T4 axles or trying to buy some losi front pivot blocks/hubs and axles??
and to be honest its to upgrade a macnum, and I run a b4 for competition/club meets and got the bits to fit out the macnum from my spares box, was hoping to share some parts and got quite a few sets of truck rims mounted up to go bashing with.
__________________
Team EDNA Racing! Hpi Savage 4.6 + innovative RC big bores & LCG chassis! - Savage 25 - Procat - Durango DEX410R - Mardave Banger x2 & carbon GT12 - Tamiya mwb & swb minis - Playmobile caravan! - cut'n'shut TL-01 - Rovan 1/5 Baja 26cc - SCX10 Defender 90 - Venom Creeper - Schumacher Mi5 - Axial Exo buggy x2 -Tamiya Hornet/Baja bug hybrid - Associated SC10 !!! Frsky 2.4ghz !! How many is too many??
|
|
#4
25-05-2010
|
||||
|
||||
|
theres not much point in trying to fit truck wheels on a buggy, the car will handle like a bag of crap
__________________
Schumacher Racing - Reedy - Schelle - TKR - Bandicoot Bodies - MIP - Nextlevelrc - Trishbits - Moss Models
|
|
#5
26-05-2010
|
||||
|
||||
|
be careful with the rear rims, I ran Losi rims on an Associated GT2. The AE axle pins are not as long, and it turned the pin in the hub and ruined it. See if you can use longer Losi pins, and make sure the wheel nut is tightened up properly. I realise this was on a gas truck that probably has more grunt than an electric truck, but if you are using brushless/lipo you may mess things up. The fronts will fit by the way, the bearings are identical. as for clearance i dont know.
Hope this helps, Cheers, Mark.
|
|
#6
28-05-2010
|
||||
|
||||
|
Had another look and the losi truck rims seem to have a lot of inboard offset as well as a lip before the bearing on the inside face, meaning the B4 front axles are a) too short to get the nut on and b) the wheel sits right over the wishbones so no lock.
This brings me to plan B - Has any one got some losi truck front end gear?? Any other plans welcomed!
__________________
Team EDNA Racing! Hpi Savage 4.6 + innovative RC big bores & LCG chassis! - Savage 25 - Procat - Durango DEX410R - Mardave Banger x2 & carbon GT12 - Tamiya mwb & swb minis - Playmobile caravan! - cut'n'shut TL-01 - Rovan 1/5 Baja 26cc - SCX10 Defender 90 - Venom Creeper - Schumacher Mi5 - Axial Exo buggy x2 -Tamiya Hornet/Baja bug hybrid - Associated SC10 !!! Frsky 2.4ghz !! How many is too many??
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Team Associated
Linear Mode
