|
#1
|
||||
|
||||
Itchy fingers
I don't know about you lot but I'm getting itchy fingers and can't wait to get racing. I've spent a fortune this week new speedo new motor new servo they where £350 alone but I think it will be worth it . When I'm picking the pieces up at the end of the straight.
Buds |
#2
|
||||
|
||||
You missed new chassis off the list.......
Perhaps we'd better not make the jumps too high!
__________________
Yz4 - Yz2 DEX210 - Cobra 4210- DEX410 RC10 Team - Manta Ray - RC10T Mini Trophy - Blizzard - Wheely King Tz4 - GT24B BMRCC Emergency back-up race controller (but only if nobody better is available) |
#3
|
||||
|
||||
And top deck...
What is the motor and speedo Dave? Are you sure your buggy can handle it
__________________
|
#4
|
||||
|
||||
Quote:
already had one and a top deck.gone for a sxx and x12 5.5 t and savox so hopefully kill the durgas buds Last edited by budfish; 30-10-2009 at 09:26 PM. Reason: z |
#5
|
||||
|
||||
sxx tc ... same as Matts?
Watch them motor temps on that X12 hopefully gonna be an awesome weeekend Andy
__________________
|
#6
|
||||
|
||||
sxx
yes same as mine andy copying fu**er well atleast there will be no more excuses why we all smoke him LMAO
|
#7
|
||||
|
||||
ANDY
andy have you changed your setup any from outdoors im using the same see what its like and take it from there????
|
#8
|
||||
|
||||
Yes Matt not changing a thing only tyres!
Been messing with the Slash but its like a bowling ball... goes well in a straight line but come the corners and ...Strike!
__________________
|
#9
|
||||
|
||||
slash
shanks has lowered his to the floor and he says its a lot better he has cut his springs to do it
|
#10
|
||||
|
||||
Hopefully the Durga wont give me much trouble through the heats as in breakages, so i`ll have a mess around with the slash.Matt have you got some more lead that you could bring with you as i wouldn`t mind adding some weight too it, think i`m gonna take it tomorrow and hopefully have a little test with it and see how it holds up! the problem will be that the tracks gonna be mega grippy so the grip roll the slash has will be amplified indoors.Just thought.... drift wheels would help
__________________
|
#11
|
||||
|
||||
lead
sorry pal ive none left if ya go to plumb base in rochdale you can get it there in small roll not sure how much though or BQ just take some sissors in with you and snip a bit of a roll
|
#12
|
||||
|
||||
No probs Matt i`ll sort something out
__________________
|
#13
|
||||
|
||||
Ive got an x12 5.5 and it just gets very very hot. My x12 6.5 and 8.5 come back at about 50 to 60 C but the last time I ran the 5.5 it came back at 120c after 7 mins with melted solder and a dry front bearing. Ive swapped the sensors over and checked the windings and theyre all fine but its just a very hot motor. Deffenately recomend the 6.5 over the 5.5 .
__________________
Mark Dyson Clown |
#14
|
||||
|
||||
Lets melt some motors boys!!
__________________
|
#15
|
||||
|
||||
Not arsed
All brand new from shop geared to manual spec so I'll throw it back at them if I think it's dodgy hell have no fury compared to buds if I think I've been conned
|
#16
|
||||
|
||||
If its the new batch of x12's then it should have the 0000 insert pre installed ( -10 degs), if not make sure you put it in, this should make it run cooler . I think mine was geared a bit high but its in my Tourer now so I'll have to wait till next season outdoor to see if the lower timing and better gearing has worked. Let me know how you get on with yours then I know if its me or the motor .
__________________
Mark Dyson Clown |
#17
|
||||
|
||||
bring it on......
am ready to roll as well am going to see how she runs though the heats and take set up from there i reckon drop her on her ass for no grip roll that seems to work,its going to be interesting no pressure on the 2wd then, see shanks is stoking the fire or ready with the tamiya clan.
__________________
Schumacher K2 Schumacher KC |
#18
|
||||
|
||||
Si`s X11 motor did the same thing as MRD`s, the solder melted but hey it is Si it reached 105 ish then game over! Is there an option with the setup you have Dave to adjust the motor timings ie via the motor or the speedo i`m guessing yes so if i were you i`d drop it down to low/normal and see how it goes... i have been advised from losi on 2s lipo`s with 4.5T no higher than normal on the motor timing , as i`ve had 2 speedo warranties now
__________________
|
#19
|
||||
|
||||
Quote:
__________________
|
#20
|
||||
|
||||
Timing
I'll pass that info on to my tech department(ie matt and ty) and I'm sure everything will be fine if it gets hot I'll drop to 18 pinion instead of the 19 easy
buds |
|
|