dex210 front wheels

[jonathan may]

so i i assume that the 210 front wheels should be in stock sometime next week with the next batch of 410v3,s ?

[Matt Howard]

anyone know if the TRF201 front wheels can be used?

[stegger]

http://www.deracing.net/store/index....y&path=130_150

DERACING are doing wheels

[AmiSMB]

Originally Posted by Matt Howard

anyone know if the TRF201 front wheels can be used?

TFR201 wheels fit but you need to a 2mm wide spacer before the inner bearing so they match up with the end of the axle.

[sunbeam]

Yuck, whats with the rivets ?

[jonathan may]

what way do people mount schumacher stagger cut on the 210 front wheel narrow and cut the wheel down or on the whole wheel.

[Big G]

run a stanley knife around the inside against the lip. After several rotations you'll find the blade will go through the rim and you can finish off the cut.

that's how I did it.

[jonathan may]

sorry what i ment was should they be fitted narrow or wide

[mattybucks]

Stagger rib no insert and narrow.
Cut stagger wide with and insert.

[ASKay]

any word on when the Durango DEX210 fronts are arriving to purchase?

[sunbeam]

Any news on spares, full stop ?

[triplesix]

Anyone who managed to fit Schumacher wheels/TD bearings in those?
No TD wheels available at my place and there's a race in 10 days, so I'll try to use the ones I have...

[neil_p]

I'm positive it has been mentioned in a previous post that a front axel that would accept Schumacher/AE front wheels would be available, I just cannot remember which post it was in, or weather it would be from Durango or another company.

If that person can confirm?

[bodgit]

Was it this by Adam
http://www.oople.com/forums/showthre...371#post569371

Wheels are due in next week.
You can 'Drill / Ream' a B4 wheel out to 10mm and then press in the Durango bearings. It will help get you away until you get the proper ones

[sunbeam]

I can CONFIRM that Schumacher and AE front wheels DO NOT FIT. The 210 bearings are to big for the Schumbacher and AE wheels. The front axles on the 210 are to big for the Schumacher and AE bearings.

[bodgit]

Originally Posted by sunbeam

I can CONFIRM that Schumacher and AE front wheels DO NOT FIT. The 210 bearings are to big for the Schumbacher and AE wheels. The front axles on the 210 are to big for the Schumacher and AE bearings.

Thats why Adam recommended reaming out AE wheels to fit TD bearings as a temporary solution.

[neil_p]

Nah it wasn't that post from Adam.

Like I said I cannot remember and I'm not going to wade through all the posts. All I can imagine is it will be a Schumacher/AE sized axel with the Durango fitment. If no one will do one I'll fabricate up a couple.

[ASKay]

I was looking at getting some made, but then decided I like TD wheels too much, so resided myself to buying new tyres, and wheels.....

just means i will be racing 4WD this weekend...

[Dazzler]

Originally Posted by neil_p

I'm positive it has been mentioned in a previous post that a front axel that would accept Schumacher/AE front wheels would be available, I just cannot remember which post it was in, or weather it would be from Durango or another company.

If that person can confirm?

Is this the post you are looking for...

http://www.oople.com/forums/showpost...0&postcount=46

And you could fit 201 wheels with some shims fitted to the stub axle first.. Might be easier for some prior to the release of these..

[neil_p]

That's the one Dazzler.

I agree the Duango wheels are better but got loads of Schumacher slims that I like to run and I don't like to cut the wheels down. Unless Durango are prepared to make a slim wheel I'll run the Schumacher ones.

Same for the rears, got loads of pin type wheels, so will run the optional cone washer and spacer for the time being.