|
#1
|
|||
|
|||
breakages on b-max2 mr
hi all this is not to put a bad post about the bmax2 more of so I no what parts I might possible need had my car 3 maybe 4 months now run it every Friday and Sunday in and out side love it such a good car but my idler gear destroyed its self last night which stopped me from racing and I have had two wheels come loose and destroy the pin slots in the wheel more my fault though for not checking wheel nuts so any one else broke anything ?
|
#2
|
|||
|
|||
I have not broke a thing on bmax2 or bmax4 at all n I've been racing them most of the year so far. Strangely enough I've had wheel nuts come loose at the 2 meets
__________________
Antony Washington Furness Radio Car Club - Chairman MB Models Team Driver KF, XB4 2014
|
#3
|
|||
|
|||
So far one rear hub carrier after a stupid jump and one front hub carrier and shock tower after hitting a tree on our track for the n-th time. Not bad for more than one year of (ab-)use, tough car!
As I am switching back to 17.5 turn for the time being, I expect to experience even less damage.
__________________
NRW Offroad Cup |
#4
|
||||
|
||||
Not broken anything yet on 2wd as of yet. As for the 4wd, I can't remember the last time I broke a thing.
Really strong, well built cars.
__________________
Team Associated Hobbywing SRT Reedy My feedback http://www.oople.com/forums/showthread.php?t=63097 |
#5
|
||||
|
||||
Breakages
I've not broke anything yet despite some big hits. I also have had a couple of wheel nuts come loose so I have just bought some serrated wheel nuts. I really hope that the yok prototype that is mentioned on another thread is a new 4wd as I am in the market for a new 4wd.
__________________
Al |
#6
|
||||
|
||||
I've not broken anything and replace the rear wheel nuts with Durango serrated ones and had no issues since
__________________
Luniemiester drives: AE B6.1 AE B6.1d AE B74 AE T6.1 AE SC6.1 Kits and parts supplied by: http://www.rccarshop.co.uk/[/size] My Feedback thread: http://www.oople.com/forums/showthre...945#post691945 |
#7
|
||||
|
||||
Serrated nuts for the rear wheels for sure.
I've seen a couple of idler gear failures on others. I checked mine last week and there was a little bit of idler coloured dust in the gearbox. Looking very carefully at one of the idlers I could see the profile of the teeth wasn't quite perfect (gone slightly hook shaped) so swaped the idlers for new. |
#8
|
|||
|
|||
With the aid of a little PTFE grease, my idler gear is as good as new after a year.
__________________
NRW Offroad Cup |
#9
|
||||
|
||||
broken chassis and gear diff gears
|
#10
|
||||
|
||||
Done an idler yesterday in leg 2 of my A final. I've noticed a few people doing idlers. Anyone know if there is an upgraded idler available?
__________________
Team Associated Hobbywing SRT Reedy My feedback http://www.oople.com/forums/showthread.php?t=63097 |
#11
|
||||
|
||||
Quote:
Not checked my idler since i built it.. might have to check and buy a spare.
__________________
-------------------------------------------------------------------------------------------------------------------
Team Yokomo - YZ-2CAL3 | YZ-2DTM3 | YZ-4SF2 | YZ-2T | YZ-2DTM Worlds | YZ-2DTM x2 | YRX-12 x2 ------------------------------------------------------------------------------------------------------------------- 10electric | Batley Buggy Club | YORCC | RHR | MB Models --------------------------------------------------------------------------------------------------------------- |
#12
|
|||
|
|||
After 5 months of hard weekly racing I finally broke something :0
After a harsh landing going over a huge table top a rear hinge pin snapped. The wishbone and hub were still in one peice tho.
__________________
Antony Washington Furness Radio Car Club - Chairman MB Models Team Driver KF, XB4 2014
|
#13
|
||||
|
||||
I 've done an idler too, and i somehow managed to bend the front c-hubs. They (only the left actually) didn't break they just bent letting the king pin out. Just replaced both of them to be sure.
__________________
Team Yokomo B-Max2MR/Reedy/ORCA/Jconcepts/AVID Bearings Team Yokomo B-Max4III/Reedy/ORCA/Jconcepts/AVID Bearings |
#14
|
|||
|
|||
3 meetings without a scratch.
Then snap goes the chassis at the back. Hopefully the new one should be out soon
__________________
Kyosho Speed Passion |
#15
|
||||
|
||||
Quote:
Need to find something more reliable.
__________________
Team Yokomo B-Max2MR/Reedy/ORCA/Jconcepts/AVID Bearings Team Yokomo B-Max4III/Reedy/ORCA/Jconcepts/AVID Bearings |
#16
|
||||
|
||||
Finally broke something on the car.....gear diff gears. Are the alloy versions available yet?
|
#17
|
||||
|
||||
So far I have broken front chassis top and bottom and a shock cap. Hitting a bench at the end of the straight at DMS full speed.
Not bad so far Sam
__________________
Sam Harris Serpent Spyder SRX-2 MM
|
#18
|
|||
|
|||
Any one now when the alloy idaler gears are coming out as I have broke to now so need the alloy ones :-(
|
#19
|
|||
|
|||
All the parts shown at Shizuoka are scheduled for June, mibosport says late June iirc.
|
|
|