|
#1
|
||||
|
||||
new lipo retainer
i was thinking about a better way to retain my trakpower 4900 lipo in the CAT as i wasn't too keen on gluing the carbon battery retainers (the battery is used in my 2WD). i didn't want to use velcro as the 4900 is too tall to get velcro under the strap and still hook over the front locating pin without looking silly.
anyway - i designed a new 3mm thick carbon retainer that uses existing holes in the chassis and holds the battery in really well - picture attached. it basically holds the battery against the servo / front bulkhead and stops the back of the pack moving left/right/backwards although the retainer is designed for trakpower 4900's, it should hold TP 3200/3800's (although i haven't tested them) Last edited by nickhudson; 06-02-2009 at 09:57 PM. Reason: added more pictures |
#2
|
||||
|
||||
Looks really tidy that
Ive used a X-6 carbon shim glued to the chasis to stop it mooving and it 'Seems' to be OK - Not had any issues yet...
__________________
|
#3
|
||||
|
||||
I'm going to use doublesided tape. I hope it'll be sticky enough for one race day.
__________________
Retired from racing
| パベルともうします、よろしくおねがいしますスロバキア人だ、今イギリスにすんでいます。| | Ralls Racing | RCSGraphicWorx - paints, paintjobs, decals, custom wear | Schumacher Racing | Mr.O inserts | |
#4
|
||||
|
||||
Great work.
I just couldn't bring myself to glue the standard retainers to my batteries, so ended up using velcro. This is a much better solution.. Nice one.. |
#5
|
||||
|
||||
thanks for the comments. i'm not knocking the schumacher designers at all as i know how hard (read impossible) it is to satisfy everyones requirements but i think the standard lipo retention system didn't take into account peoples reluctance to glue the kit retainers to their batteries thus making them difficult to fit into other cars
|
#6
|
||||
|
||||
Nick, if you want to make any more for people - put me down as no.1 on your list of enquiries - I want one fella!!!
|
#7
|
||||
|
||||
chris - i was thinking about making a few more. i have got two prototypes....
|
#8
|
||||
|
||||
Wow I want one of those! Very nice work, well done.
If you are going to make some more, put me on the list too please! |
#9
|
|||
|
|||
I'd be in for one too!
Where did you get the adonised nut etc from? If you were making more would be great if you also supplied the fixings Really don't like the battery mount system they came up with. Very fiddly to get the battery in/out too. (my locators are double sided taped on and I have velcro on the top under the bar). |
#10
|
|||
|
|||
__________________
If it ain't 200+ bhp it ain't worth it |
#11
|
||||
|
||||
I have money in my paypal account
LMK when I can buy please!!!
__________________
Blacked Out Mi4 Schumacher/Speed Passion/Black Army Racing/Owen RaCing Anodizing/NNFaN Paints/Scooter Motorworks |
#12
|
||||
|
||||
And me please.
Thanks Col.
__________________
TRF 501x - Tamiyafied Madrat - Bograt Rc10 FT T4 RC18T Lunchbox Gold X-6 squared Lrp, Novak, Robitronic, Ko Propo, Ezrun , Trakpower ,Team Scream, Demon, Microtech, Dms, Good old Jezza, Je-Spares, Bolton Model Mart, My Feedback http://www.oople.com/forums/showthread.php?t=25199 |
#13
|
||||
|
||||
hello eveyone - thanks for the interest in the battery retainer. i should clarify a few things before i make any more :-
1. i haven't tested it in anger as i've not run the car yet (waiting for the shell from Jon Miller) so can't 100% guarantee it's race proven - i have no doubt it'll be up to it but i'd rather make that clear up front. 2. the retainer definately fits TP 4900's - i can't say about any other batteries as that's all i run. if you look on the TP website it gives the footprint of the other batteries which all look very similar but the heights are different. the retainer is 3mm thick which replicates the purple spacers under the battery strap post. a thinner battery may need some foam under the strap to stop it rattling. 3. the retainer will have a small (approx. 2mm diameter) hole at the end of the outside leg to glue it to the chassis. this stops any flexing of that leg. you will have to glue it to the chassis - the hole is there to drop a tiny amount of CA glue through whilst holding the leg in position - it is less messy than trying to spread glue on the retainer and then clamping it to the chassis if, after all that, you still are interested - let me know and i'll see what i can do to get some more made. |
#14
|
|||
|
|||
I'll want one if you can get some more made up.
Alex |
#15
|
||||
|
||||
I would be interested in one. put on the list...
Thanks Big G. |
#16
|
||||
|
||||
I am still interested
|
#17
|
||||
|
||||
I'll have one....Thanks Nick
__________________
Schumacher CAT SWB, XLS,ProCAT,AERO K1(+shorty mod) 1/18th Duratrax Vendetta buggy, ST& Rally DEX410 (2009),410ULTRA- Atomic Carbon,DMX410,DEX410V5. |
#18
|
||||
|
||||
ok, let me get a price together. if i can get 15+ orders it'll work out cheaper for all.
when i have the info, i'll let you know paypal details etc... |
#19
|
||||
|
||||
Quote:
__________________
Blacked Out Mi4 Schumacher/Speed Passion/Black Army Racing/Owen RaCing Anodizing/NNFaN Paints/Scooter Motorworks |
#20
|
||||
|
||||
just making a list of potential orders. so far i've noted the following :-
1. chrislong 2. glypo 3. cassp0nk 4. jas_racing (3 off) 5. blackedoutmugen (possible 2 off) 6. colinevan 7. henga 8. minster68 9. ex-buttmonkey1969 10. chris68nufc 11. stegger 12. mharlow (2 off) 13. paul01ews to make things nice and easy, add your name to the list or PM me i should have pricing info tomorrow (they won't cost very much) edit : list updated 9/02/09 still waiting for the price but i hope to get manufacture started later this week (assuming the price is OK with you all) |
|
|