|
#1
|
||||
|
||||
![]()
if you've got one post some tips, tricks & setup info in here
__________________
o0ple Trader Feedback NE Venue's New & Old my space on YouTube CFR RCTV Channel Glenn Atterton BRCA 2005 1/10th Off-Road Veterans Champion LMP12 National Champion 2003/2004 / F3 class |
#2
|
||||
|
||||
![]()
see the site you visit regular as Gazza has done a complete build blog with pictures yes you are right www.rccircuitcars.com
|
#3
|
||||
|
||||
![]() Quote:
![]() interesting, might just phone you then ![]()
__________________
o0ple Trader Feedback NE Venue's New & Old my space on YouTube CFR RCTV Channel Glenn Atterton BRCA 2005 1/10th Off-Road Veterans Champion LMP12 National Champion 2003/2004 / F3 class |
#4
|
||||
|
||||
![]()
Great stuff was waiting for u to bell me i think the vids u andd gazza done are also brilliant helps newbies out.
![]() |
#5
|
||||
|
||||
![]()
I have and it was an interesting conversation
![]() Quote:
![]()
__________________
o0ple Trader Feedback NE Venue's New & Old my space on YouTube CFR RCTV Channel Glenn Atterton BRCA 2005 1/10th Off-Road Veterans Champion LMP12 National Champion 2003/2004 / F3 class |
#6
|
||||
|
||||
![]()
anyone got a setup yet for the new vrx ce car ?????????????
__________________
CORNWALL Grass all the way simon mills ![]() http://www.oople.com/forums/image.ph...ine=1360240269 |
#7
|
||||
|
||||
![]()
I set mine up as a normal v12 but on the front i used black rubber O rings instead of springs. And as in Pauls post leave the center washer out on the front plate for some camber.I found it better this way. and stiffen the rear a little with about 1mm droop fully loaded, batteries/shell ect. i found this works for me. oh and add a mardave sticker, it makes it faster, lol.
![]() ![]() ![]() ![]() |
#8
|
|||
|
|||
![]()
So thats an almost solid front end. How does it feel? Does the flex in the chassis help?
Makes me wonder how effect front springs are. |
#9
|
||||
|
||||
![]() Quote:
![]() |
#10
|
|||
|
|||
![]()
Run mine very hard on the front, with 52's as well, feels much better.
|
#11
|
|||
|
|||
![]() Quote:
I'll run it as is for a heat then harden up the front and compare. My only option is to pack out the spring under the e clip I think unless I put some under the stub axle and lower the front at the same time. |
#12
|
||||
|
||||
![]()
Didn't know you were going to be running the new chassis phil
|
#13
|
|||
|
|||
![]()
I'm not but I've seen several people mention hard fronts now, some using o rings instead of springs.
|
#14
|
||||
|
||||
![]()
I only ever run standard springs all round, moving to mediums if need be. But never hards. Pic of my new ce chassis:
![]()
__________________
Mardave - RCbearings uk - Kamtec |
#15
|
||||
|
||||
![]() Quote:
![]() ![]() Last edited by QuackingPlums; 18-11-2011 at 12:43 PM. Reason: Typo... doh! |
#16
|
||||
|
||||
![]() Quote:
![]()
__________________
Mardave - RCbearings uk - Kamtec |
#17
|
|||
|
|||
![]()
Karl, did you change the ball cups on the damper tube or colour them in?
|
#18
|
|||
|
|||
![]() Quote:
![]() What setup are you running? |
#19
|
||||
|
||||
![]() Quote:
![]()
__________________
Mardave - RCbearings uk - Kamtec |
#20
|
||||
|
||||
![]()
Cheers mate
![]() Speedo - Hobbywing 120A 1S (blinky) Motor - HPI Flux pro 13.5 Servo - Futaba bls551 Tyres - LB50 Fronts LB1 Rears Other than that just standard everything ![]()
__________________
Mardave - RCbearings uk - Kamtec |
![]() |
|
|